With our wide range of different products, in this category we have converters, amplifiers, insulators. Here you will find interfaces like RS232 / 485/422, or convert from RS232 to RS485 / 422. If you need a specific solution for a larger project, call in and hear our sales department for more information.
Subcategories
There are 69 products.
RS232 til TTL-konverter, DB9 hun inkl. kabel
RS232 til TTL-konverter, DB9 Han inkl. kabel
RS232 - 08/07 bit
Max. 115.2 kbit / s
FTDI chip - FT232xx.
Does not work with software license dongles
With internal jumper getting + 5VDC on pin 9
1 meter USB cable
Supports Win10 < / p>
Connect RS232/RS422/RS485 equipment to USB port
Baudrate up to 921,6 kbit/s
Select type of port by DIL switch
Supports Win7/8/10, MAC
Bi-directional RS232 to RS422 converter
Galvanic isolation
DB9 male / 12VDC power supply included
Optiskt isolerad RS232-adapter, max. 115,2 kbps, automatisk flödeskontroll, DB9-kontakt
Optoisolated RS232 for RS422 / 485 Converter
3000vdc isolation
Up to 1.2 km on the RS422 / RS485
1.2kbit/s to 115.2 kbit/s, automatic baud rate
DB9 female connector for RS232 Signal
Screw terminals for RS422 / 485 signals
Supply 10 to 30 VDC
Measuring equipment for RS232 printer port can now be connected to a parallel port (LPT port)
Parallel printer port can now be connected to a serial port (RS232)
Allows PROFIBUS master access to MODBUS TCP devices
Connect MODBUS devices to a PROFIBUS network
PROFIBUS baud rate from 9.6k to 12M
MODBUS TCP 10/100
Supply voltage: 10 - 30VDC < DIN fitting
RS-422 Serial to Fiber Media Converter
RS232 for USB printer adapter cable
connect USB printer to PC com port
automatic baud rate
power supply included
DB9 female and USB B
Supply voltage: 5VDC 100mA
GDI printers (without own emulation) are not supported
See list of supported printers under Downloads
Industrial RS232 to 422/RS485 Serial Converter/ Repeater with 2 KV Isolation, MOXA TCC-100i
RS-232 to RS-422 conversion with RTS/CTS support
RS-232 to 2-wire or 4-wire RS-485 conversion
2 KV isolation protection (TCC-100I/TCC-100I-T)
Wall and DIN-rail mounting
Plug-in terminal block for easy RS-422/485 wiring
LED indicators for power, Tx, Rx
-20 to 60°C operating temperature
max baud rate 115kb / s for 56kb / s for signal RI
Up to 1.7km at 62.5um fiber cable.
Fiber Optic line multimode, 820nm
Transmitting: RxD , TxD, DTR, DSR, RTS, CTS, DCD, RI or 5x RxD, TxD
RS232 signal including DCE / DTE
Time multiplex, full duplex
RS232 DB9 male
Plug fiber ST
overvoltage (soft) protection - supply 600W / 1ms
polarity protected with diodes on DC input
optical indication (LED) red - PWR
Yellow - INPUT signal
Green - OUTPUT signal
Supply voltage 10-30VDC or 9 - 24VAC
power consumption max. 2W
Dimensions: 76 x 55 x 115 mm
PROFIBUS TO HART Convert, Gateway
4 x HART Canals
Max. 2 pcs. HART Masters
Point-to-Point or Multi-Drop HART Mode
Possibility of connecting 15 HART modules
PWR / RUN / ERR indication LED
Built-in Watchdog
4 kV ESD Protection
Operating temperature -25-75 ℃
for DIN rail mounting
Moxa A53, DB9 W/ADAPTER
Parallel til seriel omformer
Hastighed: 300 -19.200 bit/s
Handshake: XON / XOFF
Forsyning: Strømforsyning medfølger, 9 VAC, 400 mA
CNV-PAR232 er ikke bi-direktionel og kan derfor ikke sende meldinger fra printer til pc om evt. blækstatus, ”end of paper” m.m.
RS232 galvanic isolator, 3000VAC
With dual DC-DC converter, provides isolation both ways
Transmits Tx, Rx, RTS and CTS or DSR and DTR (selected)
Up to 115 kbit / s
Entrance: DB9 female, output: DB9 male
10-30VDC, screw terminal
DIN rail
Sæt udstyr med RS232, RS422 og RS485 interface på et Profibus system.
MODBUS RTU (RS232 / 422/485) equipment for Profibus DP network
MODBUS RTU slave devices are connected to the Profibus DP network
Optoisolerated RS422 / RS485 Repeater
3000vdc Glavanic isolation
2 threads RS485 is half duplex (switch-talk)
4 threads RS485 / RS422 A full duplex (both ways at the same time)
Translator from RS422 (4-wire) for RS485 (2-wire), semiduplex
automatic directional change and baud rate.
