Converter / Amplifier / Insulator

USB-32COM-RM - 32-Port RS-232 USB-to-Serial Adapter, Metal Case, Rack-Mountable.

• High speed
• 128 byte transmit FIFO & 384 byte receive FIFO
• Serial port protected with surge protection of 10KV
• Built-in switching power supply of 100V~240V
• Standard 19-inch, 1U rackmount chassis

PROFIBUS TO HART Convert, Gateway
4 x HART Canals
Max. 2 pcs. HART Masters
Point-to-Point or Multi-Drop HART Mode
Possibility of connecting 15 HART modules
PWR / RUN / ERR indication LED
Built-in Watchdog
4 kV ESD Protection
Operating temperature -25-75 ℃
for DIN rail mounting

Gateway from Ethernet slave to PROFIBUS master
protocol / hierarchy: DP-V0 Slave
PROFIBUS Speed ​​(Kbps) in 10 step from 9.6 - 12000
speed setting is automatic
Max. Input data length: 240 byte
Max. Output data length: 240 bytes
Address setting: 0 ~ 126 Set by DIP switch or EEPROM
Ethernet protocol: TCP / UDP server / client
Configuration: Web Configuration

MODBUS RTU (RS232 / 422/485) equipment for Profibus DP network

MODBUS RTU slave devices are connected to the Profibus DP network

Adds eight high-speed RS-232/422/485 serial ports via USB connection
2k bytes transmitter and receiver
Requires no IRQ, DMA, I/O port
RS-232 max bit rates of up to 1 Mbps
RS-422/485 maximum bit rates of up to 10 Mbps
Automatic transmission buffer control for 2-wire RS-485 half-duplex operation
Biasing and terminating resistors installed on board
Supported RS-232 signals: DCD, RxD, TxD, DTR, GND, DSR, RTS, CTS, RI
Supported RS-422 signals: TxD-, TxD+, RxD+, RxD-, GND
Supported RS-485 4-wire signals: TxD-, TxD+, RxD+, RxD-, GND
Supported RS-485 2-wire signals: Data-, Data+, GND
Data Bits: 7/8
Parity: None, Even, Odd, Mark, Space
Stop Bit: 1, 2
Flow Control: Hardware (RTS, CTS), XON/XOFF
Monitor LEDs for TxD, RxD indicating port status
Built-in AC to DC switching power supply, 100VAC to 240VAC
Virtual COM port drivers available for Windows 11, 10, 8.1, 8, 7, Vista, 2003, XP, 2000
Win Server: 2000 up to 2018, Linux, MAC
Industrial quality metal case with DIN bracket for DIN rail mounting

Allows PROFIBUS master access to MODBUS TCP devices
Connect MODBUS devices to a PROFIBUS network
PROFIBUS baud rate from 9.6k to 12M
MODBUS TCP 10/100
Supply voltage: 10 - 30VDC < DIN fitting

Sæt udstyr med RS232, RS422 og RS485 interface på et Profibus system.

Serial to HART Convert
Allows 2 pcs. Hart Masters
Point-to-Point or Multi-Drop Hart Mode
Possibility of connecting 15 HART modules
Point-to-point or multi-drop HART mode
for configuration of modules
Isolated COM 1: RS-232 / 422/485
PWR / RUN / ERR INDICATION LED
Built-in Watchdog
4 kV ESD protection

Supports HART Short / Long Frame
Supports Hart Burst Mode
Supports Point-to-point or Multi-Drop Hart mode
supports connection of up to 15 Hart slave devices
Allow 2 Hart Master
HC_Tool tool for module configuration and HART communication
support firmware update via Ethernet
PWR / TXRX indication LED
4KV ESD protection
built-in watchdog
Selectable 250Ω load resistance < Br> 4 Hart Channels
Support VXCOMM Technology
Built-in Web Server for Network Setting

USB to Hart Bus Converter
to HART Short / Long Frame
to Hart Burst Mode
Point-to-point or Multi-Drop Hart mode
Up to 15 HART slave units < Br> Allow 2 Hart Master
Module Configuration Tools and HART communication
Power supplied by the USB port
Selectable 250Ω load resistance

RS485 & nbsp; recoverable RS232 controller / converter
Link to 3 x RS232 units from 1 x RS485 bus
Baud speed 300 bit/s to 115,200 bit/s
10 V DC to + 30 V DC
Dual watchdog
256 KB SRAM buffer
1 x & nbsp; RS485 address per. serial interface
Operating temperature: -25 ° to + 75 ° C
For DIN rail mounting

USB til 4 ports konverter med DB9 stil til DIN skinne montering.

• Med USB kabel og strømforsyning.
• Metal kabinet.
• 4 X RS422/485 porte
• Hastighed: optil 921.6 Kbpz
• 4 X DB9 hanstik

4-Port RS-232/422/485 USB tilSeriel Adapter, metal kabinet med forlængerkabel. Til DIN skinne montering.

• Plug & Play
• DB37 forlængerkabel til 4 DB9 serielporte
• Metal kabinet.
• 4 X RS232/422/485 porte
• High speed serielport baud rate optil 921.6K bps
• 128 byte transmit FIFO & 384 byte receive FIFO

Industrial RS422/RS485 Serial Converter/Repeater with 2 KV Isolation, MOXA TCC-120i

Boost serial signal to extend transmission distance
Boost RS422 or RS485 signal, or convert RS422 to RS485
2 KV optical isolation protection
15 KV serial ESD protection

Wall or DIN-rail mounting

Terminal block for easy wiring

Power input from terminal block
DIP switch setting for built-in terminator (120 ohms)

Optoisolerede RS232 til RS422/485 konverter
3000Vdc isolation
24Vdc, 1.2W
RS-232 (DB9)
RS485 (2-Wire) eller RS422 (4-Wire)
Speed (bps): 1.200, 2.400, 4.800, 9.600,
19.2 k, 38.4 k, 57.6 k, 115.2 k
RTS control and RS-422 (switchable)

MOXA Converter RS232 / RS422 / RS485 Fiber MultiMode, TCF-142-M-ST

Isoleret RS485 repeater til DIN skinne

MOXA USB til RS232/422/485 konverter, isoleret.

• Port powered USB to RS232 / RS485 / RS422 converter
• Optically isolated up to 2KV
• High performance and reliability MOXA brand
• 15N high retention USB type B connector
• Texas Instruments processor chip
• Supports 2-wire and 4-wire RS485
• Indication LED lights for all handshake lines
• WHQL compliant COM drivers included
• Auto detection of data speed
• Automatic Data Direction Control
• Built-in 15 KV ESD electrostatic protection
• DB9 terminal header block included
• USB cable included

Point-to-Point Fiber Converter RS232 / RS422 / RS485
Multi Mode 62.5 / 125 or 50 // 125my, wavelength 850nm
Power Supplied from 10 - 30VDC / 2 Watts
DIN Rail Bracket .
Up to 2km
ST plug

RS232 for USB printer adapter cable
connect USB printer to PC com port
automatic baud rate 
power supply included
DB9 female and USB B
Supply voltage: 5VDC 100mA
GDI printers (without own emulation) are not supported 
See list of supported printers under Downloads