Data logger for external temperature and humidity sensors
Sensors are not included - must be purchased separately, see selection
Memory for 70,000 measurements
Temperature, humidity and dew point can be displayed graphically
1-Wire and RS485 sensor interface
Up to 8 Teracom sensors can be connected
MODBUS TCP/IP support
SNMP v2 with trap alarm for 5 email recipients
Secure email
XML/JSON and HTTP API commands for client-server
Dynamic DNS, DynDNS, No-IP and DNS-O-Matic
NTP support for time synchronization
Remote firmware update
Supply voltage: 10 - 32VDC - purchase PSU
TCW210-TH is a temperature and humidity data logger with Ethernet interface. Real-time data and curves of temperature, humidity and dew point can be monitored with a standard web browser (no special software required).
The device stores all monitored parameters in internal FLASH memory. The logging takes place at the pre-set time interval and/or in an alarm mode. The memory capacity is at least 36 days if the logging is at 1 minute intervals. The log file can be uploaded on a dedicated server by HTTP Post.
The logger uses circular buffer in FLASH memory. When it is full, the new data overwrites the oldest. In this way, the FLASH memory stores the entire log all the time. There is not a command to clear the log for security reasons. A copy of the full log is always available for download.
TCW210-TH supports Teracom temperature or temperature humidity sensors. All of them can be connected either to 1-Wire interface or to more robust industrial RS485. The maximum number of sensors is 8 and it depends on which of the two interfaces is used.
TCW210-TH can start a connection (HTTP Post) to remote dedicated servers with XML or JSON file. The files contain current values for monitoring parameters. HTTP content can be sent periodically or upon pre-set alarm conditions.
Standard protocols such as SNMP, MODBUS/TCP and HTTP/API are also available for M2M applications.
TCW210-TH supports communication with ThingSpeak server. Four different parameters (channels) can be processed simultaneously.
Mains adapter - switch mode type
110-240 VAC to 12VDC/1.5A
DC plug: 5.5/2.1 mm
1 meter cable
Temperature sensor with Dallas chip - up to 8 pieces on the same bus
1-wire communication to the measuring electronics
With connector for cascade coupling to the next sensor
±0.5°C accuracy from -40°C to +85°C
12 bit resolution
Temperature sensor in the box
Very low power consumption
Each device has a unique 64 bit serial number
Temperature sensor TST300V2 with RS485 interface
±0.13°C accuracy from +20°C to +60°C
14 bit resolution
2 x RJ45 for daisy chain connection to the next sensor
IP20 sealed housing
Low power consumption
Modbus address table: see TST300 manual
Log in to danbit.dk and press DOWNLOADS
MODBUS RTU interface
GSM / LTE alarm - 4G
Configuration via USB (Windows program) or SMS
2 x digital inputs with "dry contact" or "logic level" mode
2 x analog input from 0 to 60VDC, 10 bits
2 x relay output with NO / NC switches
1-Wire interface for 4 Teracom temperature and humidity sensors
Input can be navigated with alarm text etc.
SMS alarm - up to 5 numbers
Email alarm - up to 5 email recipients, SMTP with TLS support
1 relay can be activated with calls from up to 100 telephone numbers
Push mode - XML data is sent via HTTP Post to a remote server. Server response may include relay setup.
MQTT 3.1.1 support
Firmware update "on air"
Supply voltage: 8 - 32VDC, 2Watt - additional PSU
Dimensions: 109 x 65 x 32 mm
Weight: 152g
Ivyko klaida
GSM alarm - 2G
Configuration via USB (Windows program) or SMS
2 x digital inputs with "dry contact" or "logic level" mode
2 x analog input from 0 to 60VDC
2 x relay output with NO / NC switches
1-Wire interface for 4 Teracom temperature and humidity sensors
Input from devices can be navigated with alarm text etc.
SMS alarm - up to 5 numbers
Email alarm - up to 5 email recipients, SMTP with TLS support
1 relay can be activated with calls from up to 100 telephone numbers
Push mode - XML data is sent via HTTP Post to a remote server. Server response may include relay setup.
Firmware update "on air"
Supply voltage: 8 - 32VDC, 2Watt - additional PSU
Dimensions: 107 x 72 x 32 mm
Weight: 130g
1-wire communications - several sensors can be connected to the same unit
± 3.0% relative humidity accuracy
± 0.4% relative temperature accuracy
12 bit resolution for humidity measurement
14 bit resolution for temperature measurement
Calibrated digital output
Eksellent long-term stability
Each sensor has its own unique 64-bit serial number
