Water leak detector

Water leak sensor with sensor on the underside

Output: Open Collector.30V/100mA

Active LOW.

2-color LED indicator

Supply voltage: 5 - 26VDC

Flange mounting

Dimensions: 88 x 46 x 17 mm

IP65 tight

Operating temperature: 0 to +50°C

0.1A - 10A - DC

0.1A - 10A - AC (48-65Hz)

16-bit ADC

Resolution: 0.01 A

Accuracy: +/- 1%

AC/DC mode selector

1-wire interface (max. 30 m)

Operating temperature: -2+ to +60°C

Supply voltage: 4 - 5.5VDC/ 30mA

Dimensions: 36 x 107 x 59 mm

DIN bracket

2 channel analog input module with 1-wire interface

Voltage measurement: 0-60V

Resolution: 16bit

Accuracy: +/-1%

Input is galvanically isolated

Supply voltage: 5VDC 25mA

Temperature range: -20 - +60°C

IP20

Dimensions: 120 x 36 x 60 mm

DIN mounting

2 channel current transmitter with 1-wire interface

current measurement: 0-20mA (4-20mA) current loop

Select voltage measurement: 0-10V with Mode to GND

Resolution: 16bit

Accuracy: +/-1%

Input is galvanically isolated

Supply voltage: 5VDC 25mA

Temperature range: -20 - +60°C

IP20

Dimensions: 120 x 36 x 60 mm

DIN mounting

Modbus RTU (RS485) relay module with 4 outputs
RS-485 interface supporting up to 63 nodes
Non-volatile memory that retains relay status
LED indicator for communication status
Voltage supply: 5 - 28VDC
Watchdog functionality for communication loss
Isolated relay contacts
Shrimp switch: 250VAC / 30VDC 3Amp
No inductive load on relay contact
Memory for saving settings
Built-in 120 ohm termination resistor
DIN rail mounting
Firmware update via the interface
Dimensions: 52 x 91 x 59 mm
Operating temperature: -20 - +60°C

AC and DC voltage meter with true RMS
Resolution: 24 bits
0-264VAC 0-60Hz (3 phases)
L1, L2, L3, N
0-+/-370VDC
Input impedance greater than 2.4Mohm
Modbus RTU (2-wire RS485)
Built-in RS485 termination (120 ohms)
Up to 63 units per RS485 Bus
LED for communication status
Response time: less than 50mS
Temperature: -20 - +60°C
Supply voltage: 5 - 28VDC
Dimensions: 86 x 59 x 35 mm

Global 4G LTE Controller, logger and alarm
Supports all LTE frequencies
Setup via USB, SMS and HTTP API
USB setup - use USB cable with Mini B male
2 digital "dry contacts". High on contact
2 analog inputs, 0 - 10VDC or 4-20mA input (10bit)
4 relay outputs, COM, NO and NC
1-Wire input for up to 8 Teracom sensors
1 x RS485 for max. 8 MODBUS RTU sensors
Data logger with 70,000 logs
Upload data to HTTP/HTTPS Post in XML/JSON
SMS alarm and Email alarm to 5 recipients
Push mode – XML data is sent via HTTP Post to a remote server. Responses from server may contain relay setup.
10 to 28VDC, 370mA @ 12VDC - additional PSU
Dimensions: 158 x 119 x 34 mm
Weight: 470g
Temperature: -20 - +55°C

GSM/LTE alarm - 4G - Global version

Supports all LTE frequencies

Configuration via USB (Windows program) or SMS

2 x digital inputs with "dry contact" or "logic level" mode

2 x analog inputs from 0 to 60VDC, 10 bits

2 x relay outputs with NO/NC contacts

1-Wire interface for 4 Teracom temperature and humidity sensors

Input can be navigated with alarm text etc.

SMS alarm - up to 5 numbers

Email alert - up to 5 email recipients, SMTP with TLS support

1 relay can be activated with calls from up to 100 phone numbers

Push mode – XML data is sent via HTTP Post to a remote server. Response from server may contain relay setup.

MQTT 3.1.1 support

Firmware update "over the air"

Supply voltage: 10 - 28VDC, 2Watt - optional PSU

Dimensions: 109 x 65 x 32 mm

Weight: 152g

Thermocouple module with RTU interface (RS485)

For the following sensors: J, K, T, N, E, B, R and S

24-bit resolution

+/-0.19% CJC accuracy

Supply voltage: 5 - 30VDC

Dimensions: 35 x 86 x 59 mm

Weight: 75g

DIN bracket

1-wire Temperature / Humidity sensor
Temperature -20 - +60°C
Humidity 10 - 90% RH
Temp tolerance +/-0.4°C at -10 - +60°C
Moisture tolerance ±3.0%rH at 20 - 80%rH
Long term operation ±0.25%/year at 20 to 80%rH
Long-term operation ±0.05°C/year at -10 to +60°C
Solution 0.1 %rH 0.1 °C
Power supply/consumption 4.0 to 5.5 VDC 5 mA
Dimensions 62 x 28 x 16 mm
Cable length 1 m

Web based Data Collector module with built-in WebServer

Supports MQTT 3.1.1 protocol

4 x digital input Dry - external contact without voltage

4 x analogue inputs with 0 to 10VDC, 0-20mA

4 x powerful relay outputs with NO/NC contacts

RS485 port

MODBUS RTU up to 24 registers (sensors)

Modbus TCP/IP support

Data logger with memory for 70,000 loggings

SNMP v3 support with trap alarm

4 schemes for real-time control of relays

Up to 24 independent alarms

Secure email

XML/JSON and HTTP API commands for client-server

Dynamic DNS support for DynDNS, No-IP and DNS-O-Matic

NTP time sync

Supply voltage: 10 - 28VDC - purchase PSU

Dimensions: 145 x 90 x 40 mm

Multi sensor for CO2, Temperature and Humidity
Interface: RS485 - MODBUS RTU
LED indicator for status of communication
Long-term stability based on digital signal processing
Self-calibration on fresh air for CO2 measurements
Changeable communication parameters
Non-volatile memory for all settings
Firmware update via the interface
Size: 81 x 81 x 30 mm
Weight: 66g
Supply voltage: 4,5 - 26VDC / Max. 150mA

Temperature and Humidity sensor
RS485 MODBUS RTU
Temperature: +/-0,4 °C (-10 to +60°C), max. +/-0,6°C
Resolution: 0,1°C 
Humidity: +/-3,0% RH (20 - 80% RH), max. +/-5% RH
Resolution: 0,1% RH
Supply voltage: 4,5 - 26VDC
LED indicator for status of communication
Long-term stability based on digital signal processing
RS-485 interface (2-wire) carrying up to 32 nodes
Changeable bitrate and other communication parameters
Firmware update via the interface
Size: 81 x 81 x 30 mm
Weight: 66g

Temperature and humidity sensor
1-wire interface for Teracom controller
Temperature: +/-0.4 °C (-10 to +60 °C), max. +/-0.6°C
Resolution: 0.1°C
Humidity: +/-3.0% RH (20 - 80% RH), max. +/-5% relative humidity
Solution: 0.1% RH
Supply voltage: 4.5 - 26VDC
LED indicator for communication status
Long-term stability based on digital signal processing
Changeable bit rate and other communication parameters
Firmware update via the interface
Size: 81 x 81 x 30 mm
Weight: 66g

Multi sensor for CO2 and Barometric pressure
Interface: RS485 - MODBUS RTU
LED indicator for status of communication
Long-term stability based on digital signal processing
Self-calibration on fresh air for CO2 measurements
Changeable communication parameters
Non-volatile memory for all settings
Firmware update via the interface
Size: 81 x 81 x 30 mm
Weight: 66g
Supply voltage: 4,5 - 26VDC / Max. 150mA

Multisensor for CO2 and barometric pressure
Interface: 1-wire (+/- and data)
LED indicator for communication status
Long-term stability based on digital signal processing
Self-calibration on fresh air for CO2 measurements
Interchangeable communication parameters
Non-volatile memory for all settings
Firmware update via the interface
Size: 81 x 81 x 30 mm
Weight: 66g
Supply voltage: 4.5 - 26VDC / Max. 150mA

Magnetic contact with "dry contact" output

Contact: Max. 30V/0.2Amp

Closed contact when close together.

Dimensions: 32 x 15 x 9 mm, each unit.

Holes: 3.5 mm distance: 20 mm

Supply: 200 mm

Zinc Alloy

GSM/LTE alarm - 4G

Configuration via USB (Windows program) or SMS

2 x digital inputs with "dry contact" or "logic level" mode

2 x analog inputs from 0 to 60VDC, 10 bits

2 x relay outputs with NO/NC contacts

1-Wire interface for 4 Teracom temperature and humidity sensors

Input can be navigated with alarm text etc.

SMS alarm - up to 5 numbers

Email alert - up to 5 email recipients, SMTP with TLS support

1 relay can be activated with calls from up to 100 phone numbers

Push mode – XML data is sent via HTTP Post to a remote server. Response from server may contain relay setup.

MQTT 3.1.1 support

Firmware update "over the air"

Supply voltage: 8 - 28VDC, 2Watt - optional PSU

Dimensions: 109 x 65 x 32 mm

Weight: 152g

1-wire lysmåler til synligt lys
0 - 83.000lux med 1 lux opløsning
Op til 23bit opløsning
Automatisk fuld skala justering
Kan kaskadekoples via RJ11 stik
Forsynes fra Controller med 5VDC/4mA
Maks. 30 meter kabel
Mål: 85 x 35 x 24 mm
IP30 plasthus med flange

1-wire Combi Sensor
Temperature: -20 - +60 ° C +/- 0.6 ° C
Resolution: 0.1 ° C
Humidity (Moisture): 5 -95% Rh +/- 5%
Resolution 0.1%Rh
IP54 Plastic housing, very sturdy
Up to 8 sensors on the same 1-wire
16 bits at temperature
12 bits at moisture
Supply Voltage: 4.5 / 25mW
Dimensions: 74 x 66 x 36 mm

RS485 Modbus RTU combi sensor

Temperature: -20 - +60°C +/-0.6°C

Resolution: 0.1°C

Humidity: 5 - 95% rH +/- 5%

Resolution 0.1%rH

IP54 plastic housing, very robust

Up to 32 sensors on the same RS485 bus

16 bits at temperature

12bit when wet

Supply voltage: 4.5 - 26VDC / 25mW

Dimensions: 74 x 66 x 36 mm

DIN kit for Teracom devices
2 x Bracket + 4 screws

Multi-band 4G LTE Cat.1 controller, logger and alarm

Setup via USB, SMS and HTTP API

USB setup - use USB cable with Mini B male

2 digital “dry contacts”. High on contact

4 analog inputs, 0 - 10VDC or 4-20mA input (10bit)

4 relay outputs, COM, NO and NC

1-Wire input for up to 8 Teracom sensors

1 x RS485 for max. 8 MODBUS RTU sensors

Data logger with 70,000 loggings

Upload data to HTTP/HTTPS Post in XML/JSON

SMS alarm and Email alarm for 5 recipients

Push mode – XML data is sent via HTTP Post to a remote server. Response from server may contain relay setup.

10 to 28VDC, 370mA @ 12VDC - optional PSU

Dimensions: 158 x 119 x 34 mm

Weight: 470g

Temperature: -20 - +55°C

Remote data collection, remote meter monitoring, energy management

Energy meter interface module with MODBUS RTU

RS-485 interface with up to 63 devices per BUS

Built-in 120 ohm termination resistor

Flash memory for data and setup

Voltage supply from 5 to 30VDC, 50mA at 5VDC

Galvanically isolated digital inputs - 10mS polling rate

Optional inputs: Open/Closed (dry contact and 32 bit counter)

S0 pulse counter applications:

Remote monitoring of electricity meters

Industrial process control

Remote monitoring of gas meters and water meters

Monitoring of devices with S0 outputs;

Process monitoring

DIN rail mounting

Firmware update via interface.

Dimensions: 35 x 86 x 59 mm

Get your free license key from Teracom
DAQ software for Teracom Ethernet-based measuring devices
User-friendly WEB interface for easy configuration and control
Flexible user access and management
Distributed monitoring units in "client" fashion
Alarm notification
Activity log
Graphics and data display with large visualization
Easy access to raw data, tables, export in CSV format (comma separated)
Database management
Send command to check in "server" and "client" mode
command status log