Teracom Systems / Datalogning and conrol

Water leak detector

Water leak sensor with sensor on the underside

Output: Open Collector.30V/100mA

Active LOW.

2-color LED indicator

Supply voltage: 5 - 26VDC

Flange mounting

Dimensions: 88 x 46 x 17 mm

IP65 tight

Operating temperature: 0 to +50°C

0.1A - 10A - DC

0.1A - 10A - AC (48-65Hz)

16-bit ADC

Resolution: 0.01 A

Accuracy: +/- 1%

AC/DC mode selector

1-wire interface (max. 30 m)

Operating temperature: -2+ to +60°C

Supply voltage: 4 - 5.5VDC/ 30mA

Dimensions: 36 x 107 x 59 mm

DIN bracket

2 channel analog input module with 1-wire interface

Voltage measurement: 0-60V

Resolution: 16bit

Accuracy: +/-1%

Input is galvanically isolated

Supply voltage: 5VDC 25mA

Temperature range: -20 - +60°C

IP20

Dimensions: 120 x 36 x 60 mm

DIN mounting

2 channel current transmitter with 1-wire interface

current measurement: 0-20mA (4-20mA) current loop

Select voltage measurement: 0-10V with Mode to GND

Resolution: 16bit

Accuracy: +/-1%

Input is galvanically isolated

Supply voltage: 5VDC 25mA

Temperature range: -20 - +60°C

IP20

Dimensions: 120 x 36 x 60 mm

DIN mounting

Modbus RTU (RS485) relay module with 4 outputs
RS-485 interface supporting up to 63 nodes
Non-volatile memory that retains relay status
LED indicator for communication status
Voltage supply: 5 - 28VDC
Watchdog functionality for communication loss
Isolated relay contacts
Shrimp switch: 250VAC / 30VDC 3Amp
No inductive load on relay contact
Memory for saving settings
Built-in 120 ohm termination resistor
DIN rail mounting
Firmware update via the interface
Dimensions: 52 x 91 x 59 mm
Operating temperature: -20 - +60°C

AC and DC voltage meter with true RMS
Resolution: 24 bits
0-264VAC 0-60Hz (3 phases)
L1, L2, L3, N
0-+/-370VDC
Input impedance greater than 2.4Mohm
Modbus RTU (2-wire RS485)
Built-in RS485 termination (120 ohms)
Up to 63 units per RS485 Bus
LED for communication status
Response time: less than 50mS
Temperature: -20 - +60°C
Supply voltage: 5 - 28VDC
Dimensions: 86 x 59 x 35 mm

Global 4G LTE Controller, logger and alarm
Supports all LTE frequencies
Setup via USB, SMS and HTTP API
USB setup - use USB cable with Mini B male
2 digital "dry contacts". High on contact
2 analog inputs, 0 - 10VDC or 4-20mA input (10bit)
4 relay outputs, COM, NO and NC
1-Wire input for up to 8 Teracom sensors
1 x RS485 for max. 8 MODBUS RTU sensors
Data logger with 70,000 logs
Upload data to HTTP/HTTPS Post in XML/JSON
SMS alarm and Email alarm to 5 recipients
Push mode – XML data is sent via HTTP Post to a remote server. Responses from server may contain relay setup.
10 to 28VDC, 370mA @ 12VDC - additional PSU
Dimensions: 158 x 119 x 34 mm
Weight: 470g
Temperature: -20 - +55°C

GSM/LTE alarm - 4G - Global version

Supports all LTE frequencies

Configuration via USB (Windows program) or SMS

2 x digital inputs with "dry contact" or "logic level" mode

2 x analog inputs from 0 to 60VDC, 10 bits

2 x relay outputs with NO/NC contacts

1-Wire interface for 4 Teracom temperature and humidity sensors

Input can be navigated with alarm text etc.

SMS alarm - up to 5 numbers

Email alert - up to 5 email recipients, SMTP with TLS support

1 relay can be activated with calls from up to 100 phone numbers

Push mode – XML data is sent via HTTP Post to a remote server. Response from server may contain relay setup.

MQTT 3.1.1 support

Firmware update "over the air"

Supply voltage: 10 - 28VDC, 2Watt - optional PSU

Dimensions: 109 x 65 x 32 mm

Weight: 152g

Thermocouple module with RTU interface (RS485)

For the following sensors: J, K, T, N, E, B, R and S

24-bit resolution

+/-0.19% CJC accuracy

Supply voltage: 5 - 30VDC

Dimensions: 35 x 86 x 59 mm

Weight: 75g

DIN bracket

1-wire Temperature / Humidity sensor
Temperature -20 - +60°C
Humidity 10 - 90% RH
Temp tolerance +/-0.4°C at -10 - +60°C
Moisture tolerance ±3.0%rH at 20 - 80%rH
Long term operation ±0.25%/year at 20 to 80%rH
Long-term operation ±0.05°C/year at -10 to +60°C
Solution 0.1 %rH 0.1 °C
Power supply/consumption 4.0 to 5.5 VDC 5 mA
Dimensions 62 x 28 x 16 mm
Cable length 1 m

Web based Data Collector module with built-in WebServer

Supports MQTT 3.1.1 protocol

4 x digital input Dry - external contact without voltage

4 x analogue inputs with 0 to 10VDC, 0-20mA

4 x powerful relay outputs with NO/NC contacts

RS485 port

MODBUS RTU up to 24 registers (sensors)

Modbus TCP/IP support

Data logger with memory for 70,000 loggings

SNMP v3 support with trap alarm

4 schemes for real-time control of relays

Up to 24 independent alarms

Secure email

XML/JSON and HTTP API commands for client-server

Dynamic DNS support for DynDNS, No-IP and DNS-O-Matic

NTP time sync

Supply voltage: 10 - 28VDC - purchase PSU

Dimensions: 145 x 90 x 40 mm

Multi sensor for CO2, Temperature and Humidity
Interface: RS485 - MODBUS RTU
LED indicator for status of communication
Long-term stability based on digital signal processing
Self-calibration on fresh air for CO2 measurements
Changeable communication parameters
Non-volatile memory for all settings
Firmware update via the interface
Size: 81 x 81 x 30 mm
Weight: 66g
Supply voltage: 4,5 - 26VDC / Max. 150mA

Temperature and Humidity sensor
RS485 MODBUS RTU
Temperature: +/-0,4 °C (-10 to +60°C), max. +/-0,6°C
Resolution: 0,1°C 
Humidity: +/-3,0% RH (20 - 80% RH), max. +/-5% RH
Resolution: 0,1% RH
Supply voltage: 4,5 - 26VDC
LED indicator for status of communication
Long-term stability based on digital signal processing
RS-485 interface (2-wire) carrying up to 32 nodes
Changeable bitrate and other communication parameters
Firmware update via the interface
Size: 81 x 81 x 30 mm
Weight: 66g

Temperature and humidity sensor
1-wire interface for Teracom controller
Temperature: +/-0.4 °C (-10 to +60 °C), max. +/-0.6°C
Resolution: 0.1°C
Humidity: +/-3.0% RH (20 - 80% RH), max. +/-5% relative humidity
Solution: 0.1% RH
Supply voltage: 4.5 - 26VDC
LED indicator for communication status
Long-term stability based on digital signal processing
Changeable bit rate and other communication parameters
Firmware update via the interface
Size: 81 x 81 x 30 mm
Weight: 66g

Multi sensor for CO2 and Barometric pressure
Interface: RS485 - MODBUS RTU
LED indicator for status of communication
Long-term stability based on digital signal processing
Self-calibration on fresh air for CO2 measurements
Changeable communication parameters
Non-volatile memory for all settings
Firmware update via the interface
Size: 81 x 81 x 30 mm
Weight: 66g
Supply voltage: 4,5 - 26VDC / Max. 150mA

Multisensor for CO2 and barometric pressure
Interface: 1-wire (+/- and data)
LED indicator for communication status
Long-term stability based on digital signal processing
Self-calibration on fresh air for CO2 measurements
Interchangeable communication parameters
Non-volatile memory for all settings
Firmware update via the interface
Size: 81 x 81 x 30 mm
Weight: 66g
Supply voltage: 4.5 - 26VDC / Max. 150mA

Magnetic contact with "dry contact" output

Contact: Max. 30V/0.2Amp

Closed contact when close together.

Dimensions: 32 x 15 x 9 mm, each unit.

Holes: 3.5 mm distance: 20 mm

Supply: 200 mm

Zinc Alloy

GSM/LTE alarm - 4G

Configuration via USB (Windows program) or SMS

2 x digital inputs with "dry contact" or "logic level" mode

2 x analog inputs from 0 to 60VDC, 10 bits

2 x relay outputs with NO/NC contacts

1-Wire interface for 4 Teracom temperature and humidity sensors

Input can be navigated with alarm text etc.

SMS alarm - up to 5 numbers

Email alert - up to 5 email recipients, SMTP with TLS support

1 relay can be activated with calls from up to 100 phone numbers

Push mode – XML data is sent via HTTP Post to a remote server. Response from server may contain relay setup.

MQTT 3.1.1 support

Firmware update "over the air"

Supply voltage: 8 - 28VDC, 2Watt - optional PSU

Dimensions: 109 x 65 x 32 mm

Weight: 152g

1-wire lysmåler til synligt lys
0 - 83.000lux med 1 lux opløsning
Op til 23bit opløsning
Automatisk fuld skala justering
Kan kaskadekoples via RJ11 stik
Forsynes fra Controller med 5VDC/4mA
Maks. 30 meter kabel
Mål: 85 x 35 x 24 mm
IP30 plasthus med flange

1-wire Combi Sensor
Temperature: -20 - +60 ° C +/- 0.6 ° C
Resolution: 0.1 ° C
Humidity (Moisture): 5 -95% Rh +/- 5%
Resolution 0.1%Rh
IP54 Plastic housing, very sturdy
Up to 8 sensors on the same 1-wire
16 bits at temperature
12 bits at moisture
Supply Voltage: 4.5 / 25mW
Dimensions: 74 x 66 x 36 mm

RS485 Modbus RTU combi sensor

Temperature: -20 - +60°C +/-0.6°C

Resolution: 0.1°C

Humidity: 5 - 95% rH +/- 5%

Resolution 0.1%rH

IP54 plastic housing, very robust

Up to 32 sensors on the same RS485 bus

16 bits at temperature

12bit when wet

Supply voltage: 4.5 - 26VDC / 25mW

Dimensions: 74 x 66 x 36 mm

DIN kit for Teracom devices
2 x Bracket + 4 screws

Multi-band 4G LTE Cat.1 controller, logger and alarm

Setup via USB, SMS and HTTP API

USB setup - use USB cable with Mini B male

2 digital “dry contacts”. High on contact

4 analog inputs, 0 - 10VDC or 4-20mA input (10bit)

4 relay outputs, COM, NO and NC

1-Wire input for up to 8 Teracom sensors

1 x RS485 for max. 8 MODBUS RTU sensors

Data logger with 70,000 loggings

Upload data to HTTP/HTTPS Post in XML/JSON

SMS alarm and Email alarm for 5 recipients

Push mode – XML data is sent via HTTP Post to a remote server. Response from server may contain relay setup.

10 to 28VDC, 370mA @ 12VDC - optional PSU

Dimensions: 158 x 119 x 34 mm

Weight: 470g

Temperature: -20 - +55°C

Remote data collection, remote meter monitoring, energy management

Energy meter interface module with MODBUS RTU

RS-485 interface with up to 63 devices per BUS

Built-in 120 ohm termination resistor

Flash memory for data and setup

Voltage supply from 5 to 30VDC, 50mA at 5VDC

Galvanically isolated digital inputs - 10mS polling rate

Optional inputs: Open/Closed (dry contact and 32 bit counter)

S0 pulse counter applications:

Remote monitoring of electricity meters

Industrial process control

Remote monitoring of gas meters and water meters

Monitoring of devices with S0 outputs;

Process monitoring

DIN rail mounting

Firmware update via interface.

Dimensions: 35 x 86 x 59 mm

Smoke alarm with a diameter of 15 meters
installation up to 11 meters high
With potential-free relay contact
Smoke sensitivity: EN 54-7:2000+ A1:2002
Operating temperature: -10 to +55 °C
Dimensions: Ø100 mm, h 47 mm
Weight: 100 g

Multi input Data logger for up to 70000 loggings

10/100 Mbit Ethernet

Password-protected, web-based configuration and control

4 digital inputs, compatible with S0 pulse interface

6 analog inputs with 0/10V and 0/20mA

MODBUS RTU interface for up to 24 sensors (registers)

Up to 24 channels for monitoring

Up to 24 independent alarms

SNMP v.2 support - SNMP Trap - alarm notifications

HTTP and SNMP port change - HTTP API commands

Periodic HTTP posting of XML/JSON status files to client-server systems

MODBUS TCP/IP support

Dynamic DNS with DynDNS, No-IP and DNS-O-Matic support

NTP protocol support

Supply voltage: 10 to 28V DC

Multi output module for networks with galvanic I/O

10/100 Mbit Ethernet connection

Password-protected WEB server

2 analog outputs with voltage and current generator

0 - 20mA, 4 - 20mA, 0 - 24mA

0 - 5V or 0 - 10V voltage output

12-bit resolution

4 digital (open Drain) outputs with ON/OFF or PWM

2 relays with COM, NO and NC contacts

4 scheduled actions, once or weekly

Supports NTP

SNMP v2, SNMP trap for up to 5 recipients

MODBUS TCP/IP

HTTP upload with current status in XML or JSON file to remote server

HTTP API commands in server and client mode

HTTP Post can be sent to 3 servers

DIN rail/wall mounting

10 - 28VDC/ max. 250mA - optional PSU

DAQ software til TERACOM Ethernet baserede måleenheder
Brugervenlig WEB interface for nem konfigurering og kontrol
Fleksible bruger adgang og management
Distribueret monitorering af måleenheder i “client” mode
Alarm advisering
Aktivitets log
Grafisk og data visning med stor visualisering
Nem adgang til rå-data, tabeller, eksport in .csv format (kommasepareret)
Database management
Sende kommando til kontrollere in “server” og “client” mode
Kommando status log

Modul til detektering af vekselspænding - 85 - 250VAC
Threshold +/-8 VAC
Galvanisk isolation mellem AC og digital output Open Collector
2 niveauer med jumper
Lav temperaturdirft
Strømforsynes fra AC siden

Combi sensor for temperature and humidity measurement

Modbus RTU

2 x RJ45 connectors - with daisy chain to next module

RS485 Bus to Controller.

Up to 32 devices can be connected to the Controller

3.0% relative humidity measurement accuracy

12 bit resolution for moisture measurement

14 bit resolution for temperature measurement

With mounting flanges

Excellent long-term stability

Each module has its own ID code

Temperature sensor TST300V2 with RS485 interface

±0.13°C accuracy from -20°C to +60°C

14-bit resolution

2 x RJ45 for daisy chain connection to next sensor

IP20 sealed enclosure

Low power consumption

Modbus address table: see TST300 manual

Log in to danbit.dk and press DOWNLOADS

MODBUS RTU interface

1-wire barometrisk trykmåler, 2 x RJ11 til daisy chain
Relativ præcision på 0.12hPa
Høj elektromagnetisk (EMC) immunitet
Høj linearitet og nøjagtighed
Nem installation
Eksellent langtids stabilitet
Hver enhed har egen unik 64 bit serienummer

0-20mA 4-20mA Transmitter for 1-wire output

2 x RJ11 for daisy chaining

10-bit resolution

0-20mA and 4-20mA, 0.01mA resolution (+/-2%)

Galvanic isolation

IP30 tight

Good long-term stability

Each device has a unique 64 bit serial number

1-wire current meter 0.3 to 15 Amp
For AC or DC current monitoring
Galvanically isolated

1-wire communication - 2 x RJ11 connectors for daisy chain connection
2 - 3 - 4 wire Pt100 temperature sensor - 4 wire is recommended.
Built-in A/D converter with compensation
24 bit resolution for temperature measurement
Calibrated digital output
Excellent long-term stability
Each sensor has its own unique 64 bit serial number

1-wire communication - 2 x RJ11 connectors for daisy chain coupling.
± 3.0% relative humidity accuracy.
12 bit resolution for the moisture measurement.
14 bit resolution for temperature measurement.
calibrated digital output.
Eksellent long term stability.
Each sensor has its own unique 64-bit serial number.

1-wire communications - several sensors can be connected to the same unit
± 3.0% relative humidity accuracy
± 0.4% relative temperature accuracy
12 bit resolution for humidity measurement
14 bit resolution for temperature measurement
Calibrated digital output
Eksellent long-term stability
Each sensor has its own unique 64-bit serial number

Temperature sensor with Dallas chip - up to 8 pieces on the same bus
1-wire communication to the measuring electronics
With connector for cascade coupling to the next sensor
±0.5°C accuracy from -40°C to +85°C
12 bit resolution
Temperature sensor in the box
Very low power consumption
Each device has a unique 64 bit serial number

Temperature sensor with Dallas chip - up to 8 pieces on the same bus
1-wire communication to the measuring electronics
± 0.5 ° C accuracy from -10 ° C to + 85 ° C
12 bit resolution
Aluminum head provides low thermal resistance
IP65 close
Very low power consumption
Each unit has a unique 64 bit serial number

Data logger for external temperature and humidity sensors
Sensors are not included - must be purchased separately, see selection
Memory for 70,000 measurements
Temperature, humidity and dew point can be displayed graphically
1-Wire and RS485 sensor interface
Up to 8 Teracom sensors can be connected
MODBUS TCP/IP support
SNMP v2 with trap alarm for 5 email recipients
Secure email
XML/JSON and HTTP API commands for client-server
Dynamic DNS, DynDNS, No-IP and DNS-O-Matic
NTP support for time synchronization
Remote firmware update
Supply voltage: 10 - 32VDC - purchase PSU

Web based Data Collector module with built-in WebServer

4 x digital input Dry - external contact without voltage

4 x analog inputs with 0 to 60VDC - 10mV resolution

Multiply and offset for analog inputs and sensors

1-Wire for max. 8 sensors (16 parameters)

4 x powerful relay outputs with NO/NC contacts

MODBUS TCP/IP support

SNMP v2 support with trap alarm for 5 recipients

4 schemes for real-time control of relays

Specific logic functions for relays

Secure email

XML/JSON and HTTP API commands for client-server

Dynamic DNS support for DynDNS, No-IP and DNS-O-Matic

NTP time sync

Supply voltage: 10 - 28VDC - purchase PSU

Dimensions: 145 x 90 x 40 mm

Stand-alone Data logger via Ethernet
Memory for 70,000 measurements
Can be programmed to log every 3 seconds
Password protected Web based configuration and control
2 x digital input "dry contact"
2 x analog inputs 0 to 10VDC, 10-bit resolution, 10mV display
Multiply and offset for analog input
2 x relay with NO/NC contacts
1-Wire interface for 8 sensors
SNMP v.2 support
SNMP traps up to 5 alarm types
MODBUS TCP/IP support
E-mail to 5 recipients in case of conditional alarm
HTTP API commands
NTP and dynamic DNS support
Remote firmware update
Supply voltage: 10 - 32VDC - purchase PSU

Module with password protected Web based configuration and control

1 x digital input with "dry contact" or "logic level" mode (max. 5.5VDC)

8 x relay outputs with NO/NC contacts (3Amp)

SNMP v.1 support

SNMP traps conditional alarm sending

Email transmission upon alarm

SMTP with authentication (SSL/TLS is not supported)

XML and HTTP API commands

Remote firmware update

Robust DIN-Rail/wall mounting.

Supply voltage: 10 - 14VDC

Module with password protected Web based configuration

2 x digital inputs with "dry contact" and "logic level" mode

2 x relay outputs with NO/NC contacts

With Pair between 2 modules over network with input to output

Encrypted communication

Manual or DHCP network configuration

Device ID filtering

Remote FTP firmware update.

Supply voltage: 10 - 14VDC

Module with password protected Web based configuration and control

Instant ICMP watchdog - no echo will restart the module

1-Wire interface for 2 sensors

2 x relay outputs with NO/NC contacts

2 x analog input 0 to 60VDC - 10bit resolution, 100mV display

2 x digital input with "dry contact" or "logic level" mode

Stable IP watchdog monitoring - for equipment restart

SNMP v.1 support

SNMP trap conditional messages

VLAN and MAC address filtering

Remote FTP firmware update.

Supply voltage: 10 - 14VDC - purchase PSU

Module with smart temperature and humidity measurement and control

Password protected Web based configuration and control

1-Wire interface for 2 temperature sensors

2 x analog inputs from 0 to 60VDC - 10bit resolution, 100mV display

2 x digital inputs with "dry contact" and "logic level" mode

2 x relay outputs with NO/NC contacts

Email transmission upon alarm

SMTP with authentication (SSL/TLS is not supported)

SNMP v.1

SNMP traps generated alarm

HTTP and XML API commands

Remote firmware update

Supply voltage: 10 - 14VDC

Open board til smart temperatur- eller fugt måling and styring
Password beskyttet Web baseret konfiguration og kontrol
1 x digital input med “dry contact” og “logic level” mode
1 x analog input fra 0 til 60VDC
1 relæ output med NO/NC kontakter
1-Wire input til 1 temperature eller fugtmåler
SNMP v.1 support
SNMP traps ved alarm
E-mail udsendelse ved alarm
SMTP med godkendelse (SSL/TLS er ikke supporteret)
HTTP og XML API kommandoer
Remote FTP firmware update.