Water leak detector

Water leak sensor with sensor on the underside

Output: Open Collector.30V/100mA

Active LOW.

2-color LED indicator

Supply voltage: 5 - 26VDC

Flange mounting

Dimensions: 88 x 46 x 17 mm

IP65 tight

Operating temperature: 0 to +50°C

0.1A - 10A - DC

0.1A - 10A - AC (48-65Hz)

16-bit ADC

Resolution: 0.01 A

Accuracy: +/- 1%

AC/DC mode selector

1-wire interface (max. 30 m)

Operating temperature: -2+ to +60°C

Supply voltage: 4 - 5.5VDC/ 30mA

Dimensions: 36 x 107 x 59 mm

DIN bracket

2 channel analog input module with 1-wire interface

Voltage measurement: 0-60V

Resolution: 16bit

Accuracy: +/-1%

Input is galvanically isolated

Supply voltage: 5VDC 25mA

Temperature range: -20 - +60°C

IP20

Dimensions: 120 x 36 x 60 mm

DIN mounting

2 channel current transmitter with 1-wire interface

current measurement: 0-20mA (4-20mA) current loop

Select voltage measurement: 0-10V with Mode to GND

Resolution: 16bit

Accuracy: +/-1%

Input is galvanically isolated

Supply voltage: 5VDC 25mA

Temperature range: -20 - +60°C

IP20

Dimensions: 120 x 36 x 60 mm

DIN mounting

Modbus RTU (RS485) relay module with 4 outputs
RS-485 interface supporting up to 63 nodes
Non-volatile memory that retains relay status
LED indicator for communication status
Voltage supply: 5 - 28VDC
Watchdog functionality for communication loss
Isolated relay contacts
Shrimp switch: 250VAC / 30VDC 3Amp
No inductive load on relay contact
Memory for saving settings
Built-in 120 ohm termination resistor
DIN rail mounting
Firmware update via the interface
Dimensions: 52 x 91 x 59 mm
Operating temperature: -20 - +60°C

AC and DC voltage meter with true RMS
Resolution: 24 bits
0-264VAC 0-60Hz (3 phases)
L1, L2, L3, N
0-+/-370VDC
Input impedance greater than 2.4Mohm
Modbus RTU (2-wire RS485)
Built-in RS485 termination (120 ohms)
Up to 63 units per RS485 Bus
LED for communication status
Response time: less than 50mS
Temperature: -20 - +60°C
Supply voltage: 5 - 28VDC
Dimensions: 86 x 59 x 35 mm

Global 4G LTE Controller, logger and alarm
Supports all LTE frequencies
Setup via USB, SMS and HTTP API
USB setup - use USB cable with Mini B male
2 digital "dry contacts". High on contact
2 analog inputs, 0 - 10VDC or 4-20mA input (10bit)
4 relay outputs, COM, NO and NC
1-Wire input for up to 8 Teracom sensors
1 x RS485 for max. 8 MODBUS RTU sensors
Data logger with 70,000 logs
Upload data to HTTP/HTTPS Post in XML/JSON
SMS alarm and Email alarm to 5 recipients
Push mode – XML data is sent via HTTP Post to a remote server. Responses from server may contain relay setup.
10 to 28VDC, 370mA @ 12VDC - additional PSU
Dimensions: 158 x 119 x 34 mm
Weight: 470g
Temperature: -20 - +55°C

GSM/LTE alarm - 4G - Global version

Supports all LTE frequencies

Configuration via USB (Windows program) or SMS

2 x digital inputs with "dry contact" or "logic level" mode

2 x analog inputs from 0 to 60VDC, 10 bits

2 x relay outputs with NO/NC contacts

1-Wire interface for 4 Teracom temperature and humidity sensors

Input can be navigated with alarm text etc.

SMS alarm - up to 5 numbers

Email alert - up to 5 email recipients, SMTP with TLS support

1 relay can be activated with calls from up to 100 phone numbers

Push mode – XML data is sent via HTTP Post to a remote server. Response from server may contain relay setup.

MQTT 3.1.1 support

Firmware update "over the air"

Supply voltage: 10 - 28VDC, 2Watt - optional PSU

Dimensions: 109 x 65 x 32 mm

Weight: 152g

Thermocouple module with RTU interface (RS485)

For the following sensors: J, K, T, N, E, B, R and S

24-bit resolution

+/-0.19% CJC accuracy

Supply voltage: 5 - 30VDC

Dimensions: 35 x 86 x 59 mm

Weight: 75g

DIN bracket

1-wire Temperature / Humidity sensor
Temperature -20 - +60°C
Humidity 10 - 90% RH
Temp tolerance +/-0.4°C at -10 - +60°C
Moisture tolerance ±3.0%rH at 20 - 80%rH
Long term operation ±0.25%/year at 20 to 80%rH
Long-term operation ±0.05°C/year at -10 to +60°C
Solution 0.1 %rH 0.1 °C
Power supply/consumption 4.0 to 5.5 VDC 5 mA
Dimensions 62 x 28 x 16 mm
Cable length 1 m

Web based Data Collector module with built-in WebServer

Supports MQTT 3.1.1 protocol

4 x digital input Dry - external contact without voltage

4 x analogue inputs with 0 to 10VDC, 0-20mA

4 x powerful relay outputs with NO/NC contacts

RS485 port

MODBUS RTU up to 24 registers (sensors)

Modbus TCP/IP support

Data logger with memory for 70,000 loggings

SNMP v3 support with trap alarm

4 schemes for real-time control of relays

Up to 24 independent alarms

Secure email

XML/JSON and HTTP API commands for client-server

Dynamic DNS support for DynDNS, No-IP and DNS-O-Matic

NTP time sync

Supply voltage: 10 - 28VDC - purchase PSU

Dimensions: 145 x 90 x 40 mm

Multi sensor for CO2, Temperature and Humidity
Interface: RS485 - MODBUS RTU
LED indicator for status of communication
Long-term stability based on digital signal processing
Self-calibration on fresh air for CO2 measurements
Changeable communication parameters
Non-volatile memory for all settings
Firmware update via the interface
Size: 81 x 81 x 30 mm
Weight: 66g
Supply voltage: 4,5 - 26VDC / Max. 150mA

Temperature and Humidity sensor
RS485 MODBUS RTU
Temperature: +/-0,4 °C (-10 to +60°C), max. +/-0,6°C
Resolution: 0,1°C 
Humidity: +/-3,0% RH (20 - 80% RH), max. +/-5% RH
Resolution: 0,1% RH
Supply voltage: 4,5 - 26VDC
LED indicator for status of communication
Long-term stability based on digital signal processing
RS-485 interface (2-wire) carrying up to 32 nodes
Changeable bitrate and other communication parameters
Firmware update via the interface
Size: 81 x 81 x 30 mm
Weight: 66g

Temperature and humidity sensor
1-wire interface for Teracom controller
Temperature: +/-0.4 °C (-10 to +60 °C), max. +/-0.6°C
Resolution: 0.1°C
Humidity: +/-3.0% RH (20 - 80% RH), max. +/-5% relative humidity
Solution: 0.1% RH
Supply voltage: 4.5 - 26VDC
LED indicator for communication status
Long-term stability based on digital signal processing
Changeable bit rate and other communication parameters
Firmware update via the interface
Size: 81 x 81 x 30 mm
Weight: 66g

Multi sensor for CO2 and Barometric pressure
Interface: RS485 - MODBUS RTU
LED indicator for status of communication
Long-term stability based on digital signal processing
Self-calibration on fresh air for CO2 measurements
Changeable communication parameters
Non-volatile memory for all settings
Firmware update via the interface
Size: 81 x 81 x 30 mm
Weight: 66g
Supply voltage: 4,5 - 26VDC / Max. 150mA

Multisensor for CO2 and barometric pressure
Interface: 1-wire (+/- and data)
LED indicator for communication status
Long-term stability based on digital signal processing
Self-calibration on fresh air for CO2 measurements
Interchangeable communication parameters
Non-volatile memory for all settings
Firmware update via the interface
Size: 81 x 81 x 30 mm
Weight: 66g
Supply voltage: 4.5 - 26VDC / Max. 150mA

Magnetic contact with "dry contact" output

Contact: Max. 30V/0.2Amp

Closed contact when close together.

Dimensions: 32 x 15 x 9 mm, each unit.

Holes: 3.5 mm distance: 20 mm

Supply: 200 mm

Zinc Alloy

GSM/LTE alarm - 4G

Configuration via USB (Windows program) or SMS

2 x digital inputs with "dry contact" or "logic level" mode

2 x analog inputs from 0 to 60VDC, 10 bits

2 x relay outputs with NO/NC contacts

1-Wire interface for 4 Teracom temperature and humidity sensors

Input can be navigated with alarm text etc.

SMS alarm - up to 5 numbers

Email alert - up to 5 email recipients, SMTP with TLS support

1 relay can be activated with calls from up to 100 phone numbers

Push mode – XML data is sent via HTTP Post to a remote server. Response from server may contain relay setup.

MQTT 3.1.1 support

Firmware update "over the air"

Supply voltage: 8 - 28VDC, 2Watt - optional PSU

Dimensions: 109 x 65 x 32 mm

Weight: 152g

1-wire lysmåler til synligt lys
0 - 83.000lux med 1 lux opløsning
Op til 23bit opløsning
Automatisk fuld skala justering
Kan kaskadekoples via RJ11 stik
Forsynes fra Controller med 5VDC/4mA
Maks. 30 meter kabel
Mål: 85 x 35 x 24 mm
IP30 plasthus med flange

1-wire Combi Sensor
Temperature: -20 - +60 ° C +/- 0.6 ° C
Resolution: 0.1 ° C
Humidity (Moisture): 5 -95% Rh +/- 5%
Resolution 0.1%Rh
IP54 Plastic housing, very sturdy
Up to 8 sensors on the same 1-wire
16 bits at temperature
12 bits at moisture
Supply Voltage: 4.5 / 25mW
Dimensions: 74 x 66 x 36 mm

RS485 Modbus RTU combi sensor

Temperature: -20 - +60°C +/-0.6°C

Resolution: 0.1°C

Humidity: 5 - 95% rH +/- 5%

Resolution 0.1%rH

IP54 plastic housing, very robust

Up to 32 sensors on the same RS485 bus

16 bits at temperature

12bit when wet

Supply voltage: 4.5 - 26VDC / 25mW

Dimensions: 74 x 66 x 36 mm

DIN kit for Teracom devices
2 x Bracket + 4 screws

Multi-band 4G LTE Cat.1 controller, logger and alarm

Setup via USB, SMS and HTTP API

USB setup - use USB cable with Mini B male

2 digital “dry contacts”. High on contact

4 analog inputs, 0 - 10VDC or 4-20mA input (10bit)

4 relay outputs, COM, NO and NC

1-Wire input for up to 8 Teracom sensors

1 x RS485 for max. 8 MODBUS RTU sensors

Data logger with 70,000 loggings

Upload data to HTTP/HTTPS Post in XML/JSON

SMS alarm and Email alarm for 5 recipients

Push mode – XML data is sent via HTTP Post to a remote server. Response from server may contain relay setup.

10 to 28VDC, 370mA @ 12VDC - optional PSU

Dimensions: 158 x 119 x 34 mm

Weight: 470g

Temperature: -20 - +55°C

Remote data collection, remote meter monitoring, energy management

Energy meter interface module with MODBUS RTU

RS-485 interface with up to 63 devices per BUS

Built-in 120 ohm termination resistor

Flash memory for data and setup

Voltage supply from 5 to 30VDC, 50mA at 5VDC

Galvanically isolated digital inputs - 10mS polling rate

Optional inputs: Open/Closed (dry contact and 32 bit counter)

S0 pulse counter applications:

Remote monitoring of electricity meters

Industrial process control

Remote monitoring of gas meters and water meters

Monitoring of devices with S0 outputs;

Process monitoring

DIN rail mounting

Firmware update via interface.

Dimensions: 35 x 86 x 59 mm

Get your free license key from Teracom
DAQ software for Teracom Ethernet-based measuring devices
User-friendly WEB interface for easy configuration and control
Flexible user access and management
Distributed monitoring units in "client" fashion
Alarm notification
Activity log
Graphics and data display with large visualization
Easy access to raw data, tables, export in CSV format (comma separated)
Database management
Send command to check in "server" and "client" mode
command status log

Smoke alarm with a diameter of 15 meters
installation up to 11 meters high
With potential-free relay contact
Smoke sensitivity: EN 54-7:2000+ A1:2002
Operating temperature: -10 to +55 °C
Dimensions: Ø100 mm, h 47 mm
Weight: 100 g

Multi input Data logger for up to 70000 loggings

10/100 Mbit Ethernet

Password-protected, web-based configuration and control

4 digital inputs, compatible with S0 pulse interface

6 analog inputs with 0/10V and 0/20mA

MODBUS RTU interface for up to 24 sensors (registers)

Up to 24 channels for monitoring

Up to 24 independent alarms

SNMP v.2 support - SNMP Trap - alarm notifications

HTTP and SNMP port change - HTTP API commands

Periodic HTTP posting of XML/JSON status files to client-server systems

MODBUS TCP/IP support

Dynamic DNS with DynDNS, No-IP and DNS-O-Matic support

NTP protocol support

Supply voltage: 10 to 28V DC

Multi output module for networks with galvanic I/O

10/100 Mbit Ethernet connection

Password-protected WEB server

2 analog outputs with voltage and current generator

0 - 20mA, 4 - 20mA, 0 - 24mA

0 - 5V or 0 - 10V voltage output

12-bit resolution

4 digital (open Drain) outputs with ON/OFF or PWM

2 relays with COM, NO and NC contacts

4 scheduled actions, once or weekly

Supports NTP

SNMP v2, SNMP trap for up to 5 recipients

MODBUS TCP/IP

HTTP upload with current status in XML or JSON file to remote server

HTTP API commands in server and client mode

HTTP Post can be sent to 3 servers

DIN rail/wall mounting

10 - 28VDC/ max. 250mA - optional PSU

DAQ software til TERACOM Ethernet baserede måleenheder
Brugervenlig WEB interface for nem konfigurering og kontrol
Fleksible bruger adgang og management
Distribueret monitorering af måleenheder i “client” mode
Alarm advisering
Aktivitets log
Grafisk og data visning med stor visualisering
Nem adgang til rå-data, tabeller, eksport in .csv format (kommasepareret)
Database management
Sende kommando til kontrollere in “server” og “client” mode
Kommando status log

Modul til detektering af vekselspænding - 85 - 250VAC
Threshold +/-8 VAC
Galvanisk isolation mellem AC og digital output Open Collector
2 niveauer med jumper
Lav temperaturdirft
Strømforsynes fra AC siden

Combi sensor for temperature and humidity measurement

Modbus RTU

2 x RJ45 connectors - with daisy chain to next module

RS485 Bus to Controller.

Up to 32 devices can be connected to the Controller

3.0% relative humidity measurement accuracy

12 bit resolution for moisture measurement

14 bit resolution for temperature measurement

With mounting flanges

Excellent long-term stability

Each module has its own ID code

Temperature sensor TST300V2 with RS485 interface

±0.13°C accuracy from -20°C to +60°C

14-bit resolution

2 x RJ45 for daisy chain connection to next sensor

IP20 sealed enclosure

Low power consumption

Modbus address table: see TST300 manual

Log in to danbit.dk and press DOWNLOADS

MODBUS RTU interface

1-wire barometrisk trykmåler, 2 x RJ11 til daisy chain
Relativ præcision på 0.12hPa
Høj elektromagnetisk (EMC) immunitet
Høj linearitet og nøjagtighed
Nem installation
Eksellent langtids stabilitet
Hver enhed har egen unik 64 bit serienummer

0-20mA 4-20mA Transmitter for 1-wire output

2 x RJ11 for daisy chaining

10-bit resolution

0-20mA and 4-20mA, 0.01mA resolution (+/-2%)

Galvanic isolation

IP30 tight

Good long-term stability

Each device has a unique 64 bit serial number

1-wire current meter 0.3 to 15 Amp
For AC or DC current monitoring
Galvanically isolated

1-wire communication - 2 x RJ11 connectors for daisy chain connection
2 - 3 - 4 wire Pt100 temperature sensor - 4 wire is recommended.
Built-in A/D converter with compensation
24 bit resolution for temperature measurement
Calibrated digital output
Excellent long-term stability
Each sensor has its own unique 64 bit serial number

1-wire communication - 2 x RJ11 connectors for daisy chain coupling.
± 3.0% relative humidity accuracy.
12 bit resolution for the moisture measurement.
14 bit resolution for temperature measurement.
calibrated digital output.
Eksellent long term stability.
Each sensor has its own unique 64-bit serial number.

1-wire communications - several sensors can be connected to the same unit
± 3.0% relative humidity accuracy
± 0.4% relative temperature accuracy
12 bit resolution for humidity measurement
14 bit resolution for temperature measurement
Calibrated digital output
Eksellent long-term stability
Each sensor has its own unique 64-bit serial number

Temperature sensor with Dallas chip - up to 8 pieces on the same bus
1-wire communication to the measuring electronics
With connector for cascade coupling to the next sensor
±0.5°C accuracy from -40°C to +85°C
12 bit resolution
Temperature sensor in the box
Very low power consumption
Each device has a unique 64 bit serial number

Temperature sensor with Dallas chip - up to 8 pieces on the same bus
1-wire communication to the measuring electronics
± 0.5 ° C accuracy from -10 ° C to + 85 ° C
12 bit resolution
Aluminum head provides low thermal resistance
IP65 close
Very low power consumption
Each unit has a unique 64 bit serial number

Data logger for external temperature and humidity sensors
Sensors are not included - must be purchased separately, see selection
Memory for 70,000 measurements
Temperature, humidity and dew point can be displayed graphically
1-Wire and RS485 sensor interface
Up to 8 Teracom sensors can be connected
MODBUS TCP/IP support
SNMP v2 with trap alarm for 5 email recipients
Secure email
XML/JSON and HTTP API commands for client-server
Dynamic DNS, DynDNS, No-IP and DNS-O-Matic
NTP support for time synchronization
Remote firmware update
Supply voltage: 10 - 32VDC - purchase PSU

Web based Data Collector module with built-in WebServer

4 x digital input Dry - external contact without voltage

4 x analog inputs with 0 to 60VDC - 10mV resolution

Multiply and offset for analog inputs and sensors

1-Wire for max. 8 sensors (16 parameters)

4 x powerful relay outputs with NO/NC contacts

MODBUS TCP/IP support

SNMP v2 support with trap alarm for 5 recipients

4 schemes for real-time control of relays

Specific logic functions for relays

Secure email

XML/JSON and HTTP API commands for client-server

Dynamic DNS support for DynDNS, No-IP and DNS-O-Matic

NTP time sync

Supply voltage: 10 - 28VDC - purchase PSU

Dimensions: 145 x 90 x 40 mm

Stand-alone Data logger via Ethernet
Memory for 70,000 measurements
Can be programmed to log every 3 seconds
Password protected Web based configuration and control
2 x digital input "dry contact"
2 x analog inputs 0 to 10VDC, 10-bit resolution, 10mV display
Multiply and offset for analog input
2 x relay with NO/NC contacts
1-Wire interface for 8 sensors
SNMP v.2 support
SNMP traps up to 5 alarm types
MODBUS TCP/IP support
E-mail to 5 recipients in case of conditional alarm
HTTP API commands
NTP and dynamic DNS support
Remote firmware update
Supply voltage: 10 - 32VDC - purchase PSU

Module with password protected Web based configuration and control

1 x digital input with "dry contact" or "logic level" mode (max. 5.5VDC)

8 x relay outputs with NO/NC contacts (3Amp)

SNMP v.1 support

SNMP traps conditional alarm sending

Email transmission upon alarm

SMTP with authentication (SSL/TLS is not supported)

XML and HTTP API commands

Remote firmware update

Robust DIN-Rail/wall mounting.

Supply voltage: 10 - 14VDC

Module with password protected Web based configuration

2 x digital inputs with "dry contact" and "logic level" mode

2 x relay outputs with NO/NC contacts

With Pair between 2 modules over network with input to output

Encrypted communication

Manual or DHCP network configuration

Device ID filtering

Remote FTP firmware update.

Supply voltage: 10 - 14VDC

Module with password protected Web based configuration and control

Instant ICMP watchdog - no echo will restart the module

1-Wire interface for 2 sensors

2 x relay outputs with NO/NC contacts

2 x analog input 0 to 60VDC - 10bit resolution, 100mV display

2 x digital input with "dry contact" or "logic level" mode

Stable IP watchdog monitoring - for equipment restart

SNMP v.1 support

SNMP trap conditional messages

VLAN and MAC address filtering

Remote FTP firmware update.

Supply voltage: 10 - 14VDC - purchase PSU

Module with smart temperature and humidity measurement and control

Password protected Web based configuration and control

1-Wire interface for 2 temperature sensors

2 x analog inputs from 0 to 60VDC - 10bit resolution, 100mV display

2 x digital inputs with "dry contact" and "logic level" mode

2 x relay outputs with NO/NC contacts

Email transmission upon alarm

SMTP with authentication (SSL/TLS is not supported)

SNMP v.1

SNMP traps generated alarm

HTTP and XML API commands

Remote firmware update

Supply voltage: 10 - 14VDC

Open board til smart temperatur- eller fugt måling and styring
Password beskyttet Web baseret konfiguration og kontrol
1 x digital input med “dry contact” og “logic level” mode
1 x analog input fra 0 til 60VDC
1 relæ output med NO/NC kontakter
1-Wire input til 1 temperature eller fugtmåler
SNMP v.1 support
SNMP traps ved alarm
E-mail udsendelse ved alarm
SMTP med godkendelse (SSL/TLS er ikke supporteret)
HTTP og XML API kommandoer
Remote FTP firmware update.