Converter / Amplifier / Insulator

Isoleret RS485 repeater til DIN skinne

Serial to USB converter with 1 x RS232/422/485 port

Respects +/- 11volt data signals

Galvanically isolated on the RSxxx output

Self-tuner Baud Rate

Automatic direction control

Powered from the USB port

USB connector: Type B

Supports USB 1.1, 2.0 and 3.0

COM port: terminal block

USB to Hart Bus Converter
to HART Short / Long Frame
to Hart Burst Mode
Point-to-point or Multi-Drop Hart mode
Up to 15 HART slave units < Br> Allow 2 Hart Master
Module Configuration Tools and HART communication
Power supplied by the USB port
Selectable 250Ω load resistance

Repeater and splits an RS485 signal into 4 branches
RS485 master on input polls RS485 slaves with ID
Only asked RS485 slave responds only to master
No RS485 slave can poll the RS485 bus
2-wire RS485 - semi-duplex
Extend the star bus with more M485-REP4-I
Supply: 10 - +30VDC
Temp: -25 - +75°C
For DIN-Rail mounting

Repeater and splitter of an RS485 signal
Up to 3 branches, as a star connection
It is very IMPORTANT to avoid bus reflections.
Use M485-REP3-I if the RS485 bus is to be split out for DIN assembly

Optoisolerated RS422 / RS485 Repeater
3000vdc Glavanic isolation
2 threads RS485 is half duplex (switch-talk)
4 threads RS485 / RS422 A full duplex (both ways at the same time)
Translator from RS422 (4-wire) for RS485 (2-wire), semiduplex
automatic directional change and baud rate.

MODBUS RTU (RS232 / 422/485) equipment for Profibus DP network

MODBUS RTU slave devices are connected to the Profibus DP network

Sæt udstyr med RS232, RS422 og RS485 interface på et Profibus system.

Point-to-Point Fiber converter RS232 / RS422 / RS485
Multi Mode 62.5/125 or 50//125my, wavelength 850nm
Power is supplied from 10 - 30VDC / 2 Watt
DIN rail bracket.
Up to 2km
ST connector

Optoisolated RS232 for RS422 / 485 Converter
3000vdc isolation
Up to 1.2 km on the RS422 / RS485
1.2kbit/s to 115.2 kbit/s, automatic baud rate
DB9 female connector for RS232 Signal
Screw terminals for RS422 / 485 signals
Supply 10 to 30 VDC

RS485 for RS232 or RS422 for RS232
optoisulated RS232 for RS422 / 485 Converter
supply voltage is isolated against RS232 page
Supply voltage is isolated against RS485 / 422 page
Automatic Baud rate control

RS232 galvanic isolator, 3000VAC
With dual DC-DC converter, provides isolation both ways
Transmits Tx, Rx, RTS and CTS or DSR and DTR (selected)
Up to 115 kbit / s
Entrance: DB9 female, output: DB9 male
10-30VDC, screw terminal
DIN rail

Optoisolerede RS232 til RS422/485 konverter
3000Vdc isolation
24Vdc, 1.2W
RS-232 (DB9)
RS485 (2-Wire) eller RS422 (4-Wire)
Speed (bps): 1.200, 2.400, 4.800, 9.600,
19.2 k, 38.4 k, 57.6 k, 115.2 k
RTS control and RS-422 (switchable)

Optiskt isolerad RS232-adapter, max. 115,2 kbps, automatisk flödeskontroll, DB9-kontakt

RS232 galvanic isolator, 2500VAC

Transmits Tx, Rx, RTS and CTS

Up to 115 kbit/s

Input: DB9 female, output: DB9 male

RX, TX, ON indicator

12VDC / 100mA (-12V, +gnd)

Power supply included (3.5/1.3mm)

transfer mode RS422 - full duplex
max.transfer rate 115 kb/s
max. line length 1 200 m
transfered signals RxD, TxD
selectable terminator 120R
connector RS232 D - SUB 9 pin F
connector RS422 D - SUB 9 pin M
galvanic indication (LED) red PWR, yellow RxD, green TxD
power supply 12V + -10%
input supply max. 1W
dimension 63 x 17 x 34 mm

RS232 for RS485 converter
Opto-insulated
Galvanic isolation between DC input and RS232 port
Supply voltage: 9 - 50VDC, 10 - 34VAC
Automatic flow control
Up to 1.2km Built-in Termination Resistance - Can be Disconnected
Screw Terminals

Adds eight high-speed RS-232/422/485 serial ports via USB connection
2k bytes transmitter and receiver
Requires no IRQ, DMA, I/O port
RS-232 max bit rates of up to 1 Mbps
RS-422/485 maximum bit rates of up to 10 Mbps
Automatic transmission buffer control for 2-wire RS-485 half-duplex operation
Biasing and terminating resistors installed on board
Supported RS-232 signals: DCD, RxD, TxD, DTR, GND, DSR, RTS, CTS, RI
Supported RS-422 signals: TxD-, TxD+, RxD+, RxD-, GND
Supported RS-485 4-wire signals: TxD-, TxD+, RxD+, RxD-, GND
Supported RS-485 2-wire signals: Data-, Data+, GND
Data Bits: 7/8
Parity: None, Even, Odd, Mark, Space
Stop Bit: 1, 2
Flow Control: Hardware (RTS, CTS), XON/XOFF
Monitor LEDs for TxD, RxD indicating port status
Built-in AC to DC switching power supply, 100VAC to 240VAC
Virtual COM port drivers available for Windows 11, 10, 8.1, 8, 7, Vista, 2003, XP, 2000
Win Server: 2000 up to 2018, Linux, MAC
Industrial quality metal case with DIN bracket for DIN rail mounting

Få 4 stk. RS232 porte på PC via USB porten

Forbind 4 x RS232 enheder til USB port
Metal kabinet og med vægmontering
Baudrate op til 115,2 kbit/s
Supporterer ikke hardware licens nøgler

Supporting Win10

Get 2 pcs. COM ports on PC via the USB port

Separate USB cable AM and BM

Supports Win7/8/10/11

Cable included

Connect RS232/RS422/RS485 equipment to USB port
Baudrate up to 921,6 kbit/s
Select type of port by DIL switch
Supports Win7/8/10, MAC

RS-232 serial port by connecting to a USB port

Provides DC5V/250mA to external devices - Pin 9

Compact converter

Cable length of 100 cm

Power from host USB port

LEDs indicate TxD and RxD activity

Installs as a standard Windows COM port

Full RS-232 modem control signals and hardware/software flow control

Serial port protected with 15KV ESD protection

Non-standard baud rates supported

Easy plug and play installation and RS-232 device connection

High-speed serial port with baud rate up to 921.6 kbps

Supports Windows 11, 10, 8.1, 8, 7, XP, Windows Server 2025, 2022, 2019, 2016, 2012 R2, 2012 and 2008 R2

Supports Linux Kernel version 3.0 and later

Supports Apple-provided VCP on OS X 10.9 and later

Data bit - 7/8

Stop bit - 1, 2

FTDI chip - FT232xx.

Get 1 piece. x RS485 or RS422 port via adapter connected to PC's USB port
Galvanic isolation (optical), 2KVolt
Baudrate up to & nbsp; 921.6 Kbit / s
Windows Win 7/8, Vista, Linux & Server 2000 to Server 2016 (WHQL certified)
Linux Kernel 2.4
Mac OS X 10.9, Driver Approved by Apple

Parallel til seriel omformer
Hastighed: 300 -19.200 bit/s
Handshake: XON / XOFF
Forsyning: Strømforsyning medfølger, 9 VAC, 400 mA
CNV-PAR232 er ikke bi-direktionel og kan derfor ikke sende meldinger fra printer til pc om evt. blækstatus, ”end of paper” m.m.