RS232 / RS422 / RS485 / LPT Parallel

Optoisolerede RS232 til RS422/485 konverter
3000Vdc isolation
24Vdc, 1.2W
RS-232 (DB9)
RS485 (2-Wire) eller RS422 (4-Wire)
Speed (bps): 1.200, 2.400, 4.800, 9.600,
19.2 k, 38.4 k, 57.6 k, 115.2 k
RTS control and RS-422 (switchable)

RS232 galvanic isolator, 3000VAC
With dual DC-DC converter, provides isolation both ways
Transmits Tx, Rx, RTS and CTS or DSR and DTR (selected)
Up to 115 kbit / s
Entrance: DB9 female, output: DB9 male
10-30VDC, screw terminal
DIN rail

RS485 for RS232 or RS422 for RS232
optoisulated RS232 for RS422 / 485 Converter
supply voltage is isolated against RS232 page
Supply voltage is isolated against RS485 / 422 page
Automatic Baud rate control

Optoisolated RS232 for RS422 / 485 Converter
3000vdc isolation
Up to 1.2 km on the RS422 / RS485
1.2kbit/s to 115.2 kbit/s, automatic baud rate
DB9 female connector for RS232 Signal
Screw terminals for RS422 / 485 signals
Supply 10 to 30 VDC

Point-to-Point Fiber Converter RS232 / RS422 / RS485
Multi Mode 62.5 / 125 or 50 // 125my, wavelength 850nm
Power Supplied from 10 - 30VDC / 2 Watts
DIN Rail Bracket .
Up to 2km
ST plug

Sæt udstyr med RS232, RS422 og RS485 interface på et Profibus system.

MODBUS RTU (RS232 / 422/485) equipment for Profibus DP network

MODBUS RTU slave devices are connected to the Profibus DP network

Optoisolerated RS422 / RS485 Repeater
3000vdc Glavanic isolation
2 threads RS485 is half duplex (switch-talk)
4 threads RS485 / RS422 A full duplex (both ways at the same time)
Translator from RS422 (4-wire) for RS485 (2-wire), semiduplex
automatic directional change and baud rate.

Repeater and splitter of an RS485 signal
Up to 3 branches, as a star connection
It is very IMPORTANT to avoid bus reflections.
Use M485-REP3-I if the RS485 bus is to be split out
For DIN Rail mounting

Repeater and splits an RS485 signal into 4 branches
RS485 master on input polls RS485 slaves with ID
Only asked RS485 slave responds only to master
No RS485 slave can poll the RS485 bus
2-wire RS485 - semi-duplex
Extend the star bus with more M485-REP4-I
Supply: 10 - +30VDC
Temp: -25 - +75°C
For DIN-Rail mounting

USB to Hart Bus Converter
to HART Short / Long Frame
to Hart Burst Mode
Point-to-point or Multi-Drop Hart mode
Up to 15 HART slave units < Br> Allow 2 Hart Master
Module Configuration Tools and HART communication
Power supplied by the USB port
Selectable 250Ω load resistance

Serial to USB converter with 1 x RS232/422/485 port
Respects the +/- 11 volt data signals
Galvanically isolated on the RSxxx output
Self-tuner Baud Rate
Automatic direction control
Powered from the USB port
USB connector: Type B
Supports USB 1.1, 2.0 and 3.0
COM port: terminal block

4 ports multiplexer (sæt), op til 900m, med 2500V isolering

4 ports multiplexer (sæt), op til 900m

PCI Express parallel card with 1. DB25 port
Most drivers up to Win10 available in the Download

PCI Express parallelkort med 2 stk. DB25 stik

2 RS422/485 serielle porte til PCI Express

2 x RS232 / 422/485 Ports
PCI version 2.1 (32bit) - 3.3 / 5.0V
RS232: TX, RX, CTS, RTS - Optical ISO
RS422: TXD +/-, RXD + / -, RTS, CTS, GND
RS485: Data + / Data, GND
2 x DB9 male
Up to 921.6Kbps
Built-in Termination: 120 Ohm
DOS, Windows 98, NT , 2000, XP, Win7, Win8, 2003, Linux

Isoleret RS485 repeater til DIN skinne

Seriel kort til universal PCI, høj bagplade

2 pcs. DB9 serial ports. DB25 parallel port for PCI Express

2 x serial ports. 1 x parallel port for full length Mini PCI Express

2 x RS232 serial ports with plug & amp; play
1 x TITAN BSP9216B (chipset)
1 x DB25 male connector on the card
1 x DB25 female for two DB9 male adapter cables included
Bus: universal PCI (5V and 3.3V) 32 bit 33MHz
RS232 signal: DCD, RxD, TxD, DTR, GND, DSR, RTS, CTS, RI
Max. bitrate: 921.6kbps
Each port with 16 bit FIFO for transmit & amp; review
IS support: Windows, Linux
0 ° C to 60 ° C

4 x RS232 porte på fuldlængde Mini PCI Express x1

Serielkort universal PCI, 128 bytes FIFO, optoisoleret