Surge Protection for 10/100 / 1000Mbit network
Review voltage: 5V / 300mA
review loss: Less than 0.2dB
2 x RJ45 female (in / out)
Protected Pin: 1 - 8 (data)
Threshold at 15V
Max Transient current: 5 - 15k Amp
Operating temperature: -40 - +70°C
Moisture: less than 90% RH
Size: 112 x 38 x 30 mm
Weight: 150g
Earth cable of more than 2.5kvmm must be shorter than 1 meter
Earth resistance must be less than 4 ohms
Nothing can protect against a direct lightning strike
PROT-RJ45G-PAS is network lightning protections and contains the network data link and 2 overvoltage protection schemes for DC controls that will ensure that your system and equipment are protected from overvoltage damage caused by indirect lightning strikes or transients in connection with thunderstorms. Nothing can protect against a direct fulfillment.
This product is designed according to IEC 61000-4-5. Has excellent performance and high power capacity that can effectively prevent equipment damage caused by immediate increase in the potential difference between the power supply, network and other equipment. Protection circuits at multiple levels, low residual stress and good protection power. Suitable for overvoltage protection of network databulin and power supply for Ethernet power supply line. Important for the transient protection works is the ground cable. It must be at least 2.5 square etc. and as short as possible - preferably below 1 meter. Soil resistance must be below 4 ohms.
Transient protection for 10/100/1000 Mbit networks
10kV to ground.
2 x RJ45 female.
Ground wire should be connected.
4 x 10/100/1G/2.5G/5GBASE-T Gbit RJ45 data input
4 x 10/100/1G/2.5G/5GBASE-T Gbit RJ45 data + PoE output
100~240VAC, 3.33Amp PSU with DC 52V~54V power output
Complies with 802.3bt PoE Plus Plus end-span and mid-span PSE
Backward compatible with IEEE 802.3at PoE Plus end-span/mid-span PSE
Up to 4 IEEE 802.3at/IEEE 802.3bt PoE devices powered
4 x PoE ports with 90-watt 802.3bt PoE++ type 4 PSE or 95-watt PoH PoE injector function
4 x PoE ports support 802.3at end-span/mid-span PoE+ 36-watt injector function
DIP switch for 802.3bt, PoH and Force mode selection
Auto detects if devices can be PoE powered (PD)
Circuit protection prevents power interference between ports
Forwards both Ethernet data and PoE power to remote device over a 100-meter distance
EEE 802.3 Ethernet, IEEE 802.3u Fast Ethernet., IEEE 802.3ab Gigabit Ethernet
IEEE 802.3bz 2.5G/5GBASE-T, IEEE 802.3af Power over Ethernet, IEEE 802.3at Power over Ethernet Plus
IEEE 802.3bt Power over Ethernet Plus Plus
Dimensions: 94 x 70.3 x 39.2 mm
Weight: 275g
Enclosure: Metal case
Managed Poe+ Switch with 48 x RJ45 and 4 x SFP + slot
48 x RJ45 10/100/1000Mbit with PoE+
Up to 36 watts per port - max. Total 400W / 720W
720watt at both 230VAC and 56VDC Input
4 x SFP + slot for 1Gbit / 2.5Gbit and 10Gbit SFP Fiber modules
Redundant Ring, Fast Recovery
Layer 3 VLAN routing
Internal temperature control
IGMP Snooping, Spanning Tree Protocol
MLD Snooping (IPv6)
Management, SNMP, DHCP Server, SMTP
Redundant Voltage Supply Input
Dim: 440 x 300 x 45 mm (1U)
Weight: 5kg
Operating temperature: 0 - +50°C
Supply voltage: 100 - 250VAC, 36 - 60VDC
Converts the AUI port to the fiber cable connection.
Only intended for mounting directly on the network card or HUB
part for isolating the PC from the network or against the frame potential; differences between different supply networks
Max. cable lengths: AUI 50 meters, fiber optic 2000 meters
Power supplied from the AUI port that delivers 10 - 15 VDC / 200 mA
Plugs: DB15 male connector for AUI port and ST connector for fiber optic cable
