El-magnets / Electronic locks / Alarms / Access Systems

Tilbehør: Strømforsyning til IRISID-7111-U1

Reading of license plates with the speed of 0-200 km / h
can register license plates for up to four lanes to 5-Megapixel resolution at 30 fps
Built-in infrared white LED (approximately 60 meters)
RJ45 gigabit port
Sound alarm
ONVIF support
Motion detection
WDR
Micro SD
PoE
12VDC / 24VAC
Extended operating temperature -40 - 60 °

Payment system for vending machines, doors etc.
Accepts contactless & nbsp; chip, magnetic stripe and MobilePay
GSM (SMA) and LAN (RJ-45)
2 x digital outputs. & nbsp;
1 x deaktiveringsindgang. Can be configured to deactivate the machine
Can be connected to a vending machine, washing machine, door, etc.
Web-based control panel, can be operated over the Internet
Support for setup can be purchased
Comes with SIM card
User agreement with service provider is required

NOTE: Contract with Danbit A / S and User Agreement with service supplier MUST be established before purchase!

Payment system with touch display.
accept contactless, chip, magnetic stripe and mobilepay.
GSM antenna connector MMCX to 6 digital outputs. Can be programmed with the time difference when paying. To 6 deaktiveringsindgang2. Can be configured to disable the machine
can be connected to a vending machine, washing machine, door, etc.
Web-based control panel.
Communications Internet or WiFi or 4G
Support for setup can be purchased.
Supplied with SIM card (4G)
Supply voltage: 10 - 24VDC, 10 - 42VAC / 2Amp (power supply included)

BEMÆRK: Kontrakt med DANBIT A/S og Brugeraftale med serviceleverandør SKAL etableres før køb!

Betalingssystem med touch display.
All-in-one med POS og Data-kommunikation i samme hus
Accepterer kontaktløse kort og MobilePay.
GSM antennestik MMCX stik
6 digitale OC. pulsudgange til automat/vendingmaskine, maskiner, døre etc.
6 digitale indgange, inhibit, for at stoppe køb ved mangel/fejl
Konfigureres via platform med priser og funktioner
Kan tilkobles en salgsautomat, vaskemaskine, dør, osv
Web-baseret eller MQTT Cloud
Kommunikation: LAN eller 4G
Support til opsætning kan tilkøbes.
Leveres med SIM kort klar til funktioneopsætning
Forsyningsspænding: 10-24VDC, 10-42VAC / 2A (PSU medfølger ikke)

Vinkelbeslag kit med 3 dele
Til indadgående dør

Easy install
Simple to set up
Promotes hands hygiene and germs free at workplace
Hands hygiene traceability
Interface: Wire, RS232, RS485, Wiegand
Power require: 9-12VDC/AC / 1A
With Relay to be connected to electronic door lock
Weight: 110g
Size: 90 x 85 x 40 mm

For 19mm mounting hole
12VDC
IP65
NO/COM/NC
​Momentary reset
Metal

Radiostyret PC-sikkerhedslås til USB-porten

Beskytter PC’en mod at andre kan bruge den.
Radiomodtager til USB-porten og lille sender til lommen.

RS232 serielport interface til WA-BASE+

Monteringsdåse i plastik 115 x 43 x 32 mm

ABS plastic house for Exit button
target: 38.5 x 38.5 x 48 mm
Center hole: 20 mm
4 x mounting holes for attachment
rubber gasket included

Compact motor-controlled lock with separate pawl
Control voltage - 12VDC
With door-closed status
Holding force: 50 kg
Operating temp. -10 ° C - + 55 ° C
Dimensions: 41 x 35 x 19mm
Pal: ø9mm, 18mm
Weight: 0.11kg
Can be used on wood, aluminum and metal

Door switch for access controls - EXIT button.
make contact by pressing
Contact: NO / COM
Max. 36VDC 3Amp
cast aluminum, steel button
Operating temperature -20 - + 50 ° C
Dimensions: 83 x 32 x 25 mm | Weight: 135g

Tilbehør til tyverialarm ALARM-GSM-BASE
Indstrålingsbeskyttet
Detektionsafstand 6-8 meter
360 graders vinkel måling
installationshøjde 3-5 meters
Forsynes med 3.6V lithium batteri

Robust aluminum housing for EXIT button
Dimensions: 38.5 x 38.5 x 38 mm
Center hole: 20 mm
4 x mounting holes for attachment
3 mm extruded alu
Polished surface

Trådløs lysføler til WA-BASE+

Tilbehør til tyverialarm ALARM-GSM-BASE
Forbindes trådløst til alarmsystem
Trådløs sirene med nem stik kontakt montering

Monteringsboks til mikrobølgebarriere

Tilbehør til tyverialarm ALARM-GSM-BASE
Tilbehør til tyverialarm WKEY kodelæser
Forbindes trådløst til alarmbase
Tilkobling af flere brugere med forskellige adgangskoder
Kan slå alarm til og fra via adgangskode
Forsynes med lithium batteri

Trådløs magnetkontakt til WA-BASE+

Door switch for access control - EXIT button.
End contact by pressure
Contact: NO/NC/COM
Max. 36VDC 3Amp
Cast aluminum body, steel button
12VDC LED supply
Operating temperature: -20 - +50°C
Dimensions: 80 x 30 x 24 mm

Angled bracket for the door-magnet-yx35 types.
for attaching the holdemagnet.
1 part of extruded aluminum
screws included
target: 260 x 55 x 33 mm
anodized

18500 Lithium-Ion battery
Rated voltage: 3.7V
Capacity: 2040mAh
Max. load: 3.8A
Operating temperature: +10 ~ + 45 ° C
Charging method: CC-CV
Dimensions: 18.5 x 49.5 mm
Weight: 36.5g
Without protection circuit

Accessories for DOOR-MAGNET-LOCK6
Angle bracket for outswing door
The set consists of 1 part
Strong aluminum profile
Dimensions: See drawing

Accessories for DOOR-MAGNET-MI
angle fittings for outward door (outswing)
The kit consists of 1 part
heavy aluminum profile
Dim: See drawing

Accessories for Door-Magnet-V12CB
L-angle bracket for outward door (outswing)
The kit consists of 1 part
heavy aluminum profile
target: See drawing

Syge og ældre alarm til WA-BASE+

Electronic Mini Lock
12VDC / 1A
Goal: 80 x 65 x 14 mm
Weight: 260g

Output contact for access control with cunduct / breaking function
robust plastic house with steel Back plate
Contact: NO / NC / COM
Momentary Contact press
Contact: Max 3A
Size: 86 x 86 x 42 mm
Passive Exit Button

Tilbehøt to DOOR-MAGNET-MINI
bracket for mounting the door magnet on the side of the frame
Strong Aluminum

Rev: LO

Thermal sensor for mounting
Dallas DS18B20 Chip
5 Meters

number of channels 2
Coil Voltage 24Vdc
Load 10A, AC 250/125V, DC30V/28V
4.3 x 4.3 x 2cm/1.7" x 1.7" x 0.78"(L*W*H)

Angled bracket for the door-magnet-yx35 types.
for attaching the holdemagnet.
1 part of extruded aluminum
Screws included
Dim: 265 x 73 x 45 mm
anodized

Accessories for DOOR-MAGNET-LOCK
angle fittings for outward door (outswing)
The kit consists of 1 part
heavy aluminum profile
Dim: See drawing

Mounting angle for DOOR-MAGNET-V8 for outward-facing door. The angle clamp is mounted on the lower edge of the door frame.
It is very important that the anchor plate is mounted floating suspended and that it can come into 100% contact with the holding magnet.

Accessories DOOR-MAGNET-MI
bracket for mounting on the side of the frame
Strong aluminum profile
Dim: 170 x 37 x 30 mm

angle bracket for mounting on frame
for outward door

MDB Male and Female
DEX Male and Female

Waterproof and sunscreens
black | Material: ABS plastic
Dimensions: 15cm x 10.4cm x 9cm
Simple to install and good quality

Tilbehør til ALARM-GSM-BASE
Tilbehør til ALARM-GSM-REPEATER
Dobbelt sensor med infrarød og bevægelse
Undgår falske alarmer
opdagelses distance 8 til 12 meter

Panelmonterbar EXIT contact for access
Contact COM / NO / NC
Brushed aluminum with green button
Not vandal proof 
Dimensions: 112 x 70 mm
Contact up to 2 Amp

Accessories for DOOR-MAGNET+
angle bracket for outward door (outswing)
The kit consists of 1 part
heavy aluminum profile
target: See drawing

Output contact for access
Stainless brushed steel button steel
Acquisition metal housing for wall
Contact NO / NC / COM
Dimensions: 91 x 28 x 20mm
Contact: max 2A

Panelmonterbar EXIT contact for access
Contact: COM / NO / NC
Brushed aluminum with red button
Not vandal proof
Dimensions: 112 x 70 mm
Contact up to 2 Amp

Temperature sensor for mounting
10 m wire
Dallas DS18B20 Chip
With copper bracket for vertical mounting (M6, 6mm diameter mounting hole)
Measuring range: -10 to + 85 ° C Accuracy on +/- 1 ° C

Angle bracket for mounting on frame
for fitting to outward door

Mounting bracket for Door-Magnet-Yx28 types.
for inward doors.
2 parts of extruded aluminum
Screws included
target: 250 x 49 x 30 mm and 180 x 50 x 50 mm
anodized

Accessories for Door-Magnet-V12
Mounting the Hold Magnet on side of Karm
mounting door plate If this is necessary
for outward door (outswing)
Heavy Aluminum profile
Dim: L 220 x D 70 x B 45 mm

Residual sale

USB connection
Demoprogram included
API included.
OS up to and with Vista

Temperature gauge
1.8 Meter cable
Dallas DS18B20 Chip

Tænd/sluk via lysnet. Benyttes med  WA-SWITCH via lysnet (samme fase) til  WA-BASE+

Mounting box in metal for EXIT button, cast alu
Size: 112 x 70 x 32 mm

Z Fittings for DOOR-MAGNET-V8
for inward door
consists of 3 parts
Extruded aluminum

Projektørlamper til oplysning til brug af video overvågning

Trådløs røgdetektor til WA-BASE+

Trådløs passiv infrarød justerbar rumføler til WA-BASE+

The switch is for non-contact access.
Up to 10 cm aktiveringsafstens (10 - 100mm)
Touchless EXIT contact with relay output
IR motion technology
Adjustable sensitivity
With blue and green LED
Relay switches to 12 - 28VDC, 3Amp
Stainless steel front plate
Supply voltage: 12VDC
Dimensions: 86 x 86 mm

MDB Male and Female
EXT-MCR
TEMP
GND
DOOR OPEN
DEX Male and Female
RS232

angle bracket for frame
for outward door

Designed for Nayax payment terminals and CCI coffee machines
RS232 Male DB9 connector for interface with coffee machines.
Power(DC), ethernet(RJ45) and external reader(RJ11) ports.
Eliminates the need for CCI to MDB converters

Trådløs indendørssirene til WA-BASE+

Door magnet with holding power up to 45 kg
Aluminum + steel and vandal-proof
Supply voltage for team: 12 or 24VDC, 4 Watt
Automatic switching between 12 and 24VDC
The door is locked with applied voltage
No holding power without tension
Operating temperature: -10 - 55°C
Magnet: 70 x 31 x 20 mm
Amatur plate: 60 x 32 x 8 mm
Weight: 300g
Purchase additional access control - see Accessories

Mounting bracket Kit. 3 parts
for inward door

Mounting bracket kit. 3 parts
To inward door

Tilbehør til ALARM-GSM-BASE
Tilbehør til ALARM-GSM-PIR-UD
Kan blive trådløst tilsluttet til en alarmbase
Til tilslutning af kablede alarmsensorer
Til udendørs brug + stænktæt
Forsyningsspæning: 13.8V 200mA

Accessories for door-magnet-mi
z-angle brackets for inward door (Inswing)
The kit consists of 3 parts
heavy aluminum profiles
target: See drawing

Infrared light barrier
Up to 7 meters between the IR emitter and reflector
transmitter is powered. Passive round reflective piece
Power supply: 12-24 V DC / AC (not included)
Relay: max 36V 1A
Terminal: DC input Relay output: COM, NO (normally open contact)
Temperature: -20 ~ +60°C
Dimensions: 40 x 35 x 100 mm (W x D x H)

Power socket for door frame, w / monitor funk., 45 mm
Holding force: 900 kg.
Voltage: 12 VDC, 250 mA. Not included. For example, use DC12V / 1A-R-Q
Dimensions: 202 x 45 x 32 mm (H x W x D)
max. (H x B)

Electric strike for door frame, with lock monitor, 38 mm
with lock open without excitement
with lock closed without excitement
Force: 450kg
Voltage: 12VDC 300mA polarity independent
Lock Monitor: COM, NC NO output
Buy: DC12V/1A-R-Q
Dim: 202 x 36.5 x 27 mm

Special door fittings for DOOR-MAGNET + E + S
L-Bracket: 50x33x251mm (WxDxL)
Z-Bracket: 50x100x190 mm (BxDxL)

Electric magnetic lock plates for gates and doors
Holding force is 250kg
Supply voltage 12VDC, minimum 6Watt
Consists of electronic magnetic and strong metal plate to the door / frame
Dimensions: 251 x 25 x 47mm
plate: 185 x 12 x 38mm
Closed indicator (contact)

Fjernstyrings-sender over lysnet (samme fase) til WA-BASE+