Module with password protected Web based configuration and control
1-Wire interface for 2 sensors
2 x relay outputs with NO / NC contacts
2 x analog input with 0 to 60VDC
2x digital input with "dry contact" or "logic level" mode
Stable IP watchdog monitoring - for restarting equipment
SNMP v.1 support
SNMP trap conditional messages
VLAN and MAC address filtering
Remote FTP firmware update.
12VDC - purchase PSU
Remote collection of data, remote meter monitoring, energy management
Energy Meter Interface Module with MODBUS RTU
RS-485 interface with up to 63 units per BUS
Built-in 120 ohm termination resistor
Flash memory data and setup
Power supply from 5 to 32VDC, 25mA at 5VDC
Galvanic isolated digital input - 10mS pollinghastighed
Optional inputs: Open / Closed (dry contact and 32 bit counter)
S0 pulse counter applications :
Remote monitoring of electricity meters
Industrial process control
Remote monitoring of gas meters and water meters
monitoring devices with S0 outputs;
process monitoring
DIN rail mounting
Firmware update via interface.
Dim: 35 x 86 x 59 mm
GSM-alarm - ONLT FOR 2G
Setup via USB with Windows setup program, SMS and HTTP API
2 digital "dry contact" inputs
2 analog inputs, 0 - 10VDC - with resistance can be changed to input
2 mA analog inputs, 0 -10VDC or 0-20mA, 10bit (WEB control)
4 relay outputs, NO and NC
1-wire input for up to 8 Teracom sensors
RS485 interface for max. 8 MODBUS RTU sensors
data logger with memory for 70,000 logs
Upload data to HTTP Server
SMS alert to max. 5 recipients
Email alert for max. 5 receivers (SMTP with TLS support)
relay outputs with calls
12 to 24VDC, 350mA @ 12VDC - acquisitions PSU
1-wire temperature and humidity meter 12 bit resolution when measuring moisture 14 bit resolution when measuring temperature Good long-term stability LED communication indicator Dimensions: 99 x 66 x 36 mm Weight: 70g
1-wire Combi Sensor
Temperature: -20 - +60 ° C +/- 0.6 ° C
Resolution: 0.1 ° C
Humidity (Moisture): 5 -95% Rh +/- 5%
Resolution 0.1%Rh
IP54 Plastic housing, very sturdy
Up to 8 sensors on the same 1-wire
16 bits at temperature
12 bits at moisture
Supply Voltage: 4.5 / 25mW
Dimensions: 74 x 66 x 36 mm
Data logger for external temperature and humidity sensors Sensors are not included - must be purchased separately, see selection Memory for 70,000 measurements Temperature, humidity and dew point can be displayed graphically 1-Wire and RS485 sensor interface Up to 8 Teracom sensors can be connected MODBUS TCP/IP support SNMP v2 with trap alarm for 5 email recipients Secure email XML/JSON and HTTP API commands for client-server Dynamic DNS, DynDNS, No-IP and DNS-O-Matic NTP support for time synchronization Remote firmware update Supply voltage: 10 - 32VDC - purchase PSU
Stand-alone Data logger via Ethernet Memory for 70,000 measurements Can be programmed to log every 3 seconds Password protected Web based configuration and control 2 x digital input "dry contact" 2 x analog inputs 0 to 10VDC, 10-bit resolution, 10mV display Multiply and offset for analog input 2 x relay with NO/NC contacts 1-Wire interface for 8 sensors SNMP v.2 support SNMP traps up to 5 alarm types MODBUS TCP/IP support E-mail to 5 recipients in case of conditional alarm HTTP API commands NTP and dynamic DNS support Remote firmware update Supply voltage: 10 - 32VDC - purchase PSU
Multi sensor for CO2 and Barometric pressure Interface: RS485 - MODBUS RTU LED indicator for status of communication Long-term stability based on digital signal processing Self-calibration on fresh air for CO2 measurements Changeable communication parameters Non-volatile memory for all settings Firmware update via the interface Size: 81 x 81 x 30 mm Weight: 66g Supply voltage: 4,5 - 26VDC / Max. 150mA
Multisensor for CO2 and barometric pressure Interface: 1-wire (+/- and data) LED indicator for communication status Long-term stability based on digital signal processing Self-calibration on fresh air for CO2 measurements Interchangeable communication parameters Non-volatile memory for all settings Firmware update via the interface Size: 81 x 81 x 30 mm Weight: 66g Supply voltage: 4.5 - 26VDC / Max. 150mA
Multi sensor for CO2, Temperature and Humidity Interface: RS485 - MODBUS RTU LED indicator for status of communication Long-term stability based on digital signal processing Self-calibration on fresh air for CO2 measurements Changeable communication parameters Non-volatile memory for all settings Firmware update via the interface Size: 81 x 81 x 30 mm Weight: 66g Supply voltage: 4,5 - 26VDC / Max. 150mA
Web based data collector module with built-in Web server
4 x digital input dry - External contact without voltage
4 x analog inputs with 0 to 60vdc - 10mv resolution
multiplier and offset for analog inputs and sensors
1-wire for a maximum of 8 sensors (16 parameters)
4 x Powerful relay outputs with No / NC Contacts
Modbus TCP / IP Support
SNMP V2 Support with Trap Alarm for 5 Recipients
4 PCS. Forms for real-time control of relay
Specific logical functions for relays
Secured email
XML / JSON and HTTP API commands for Client server
Dynamic DNS support for Dyndns, No-IP and DNS- O-Matic
NTP TimeSync
Supply voltage: 10 - 32VDC - Buy PSU
Dim: 145 x 90 x 40 mm
GSM alarm - 2G Configuration via USB (Windows program) or SMS 2 x digital inputs with "dry contact" or "logic level" mode 2 x analog input from 0 to 60VDC 2 x relay output with NO / NC switches 1-Wire interface for 4 Teracom temperature and humidity sensors Input from devices can be navigated with alarm text etc. SMS alarm - up to 5 numbers Email alarm - up to 5 email recipients, SMTP with TLS support 1 relay can be activated with calls from up to 100 telephone numbers Push mode - XML data is sent via HTTP Post to a remote server. Server response may include relay setup. Firmware update "on air" Supply voltage: 8 - 32VDC, 2Watt - additional PSU Dimensions: 107 x 72 x 32 mm Weight: 130g
GSM / LTE alarm - 4G Configuration via USB (Windows program) or SMS 2 x digital inputs with "dry contact" or "logic level" mode 2 x analog input from 0 to 60VDC, 10 bits 2 x relay output with NO / NC switches 1-Wire interface for 4 Teracom temperature and humidity sensors Input can be navigated with alarm text etc. SMS alarm - up to 5 numbers Email alarm - up to 5 email recipients, SMTP with TLS support 1 relay can be activated with calls from up to 100 telephone numbers Push mode - XML data is sent via HTTP Post to a remote server. Server response may include relay setup. MQTT 3.1.1 support Firmware update "on air" Supply voltage: 8 - 32VDC, 2Watt - additional PSU Dimensions: 109 x 65 x 32 mm Weight: 152g
Web based Data collector module with built-in WebServer Supports MQTT 3.1.1 protocol 4 x digital input Dry - external contact without voltage 4 x analogue inputs with 0 to 10VDC, 0-20mA 4 x powerful relay outputs with NO/NC contacts RS485 port MODBUS RTU up to 24 registers (sensors) Modbus TCP/IP support Data logger with memory for 70,000 logs SNMP v3 support with trap alarm 4 pcs. schemes for real-time control of relay Up to 24 independent alarms Secure email XML/JSON and HTTP API commands for client-server Dynamic DNS support for DynDNS, No-IP and DNS-O-Matic NTP time sync Supply voltage: 10 - 32VDC - purchase PSU Dimensions: 145 x 90 x 40 mm
GSM/LTE alarm - 4G - Global version Supports all LTE frequencies Configuration via USB (Windows program) or SMS 2 x digital inputs with "dry contact" or "logic level" mode 2 x analogue input from 0 to 60VDC, 10 bits 2 x relay output with NO/NC contacts 1-Wire interface for 4 Teracom temperature and humidity sensors Input can be navigated with alarm text etc. SMS alarm - up to 5 numbers Email alarm - up to 5 email recipients, SMTP with TLS support 1 relay can be activated with calls from up to 100 phone numbers Push mode – XML data is sent via HTTP Post to a remote server. Responses from server may contain relay setup. MQTT 3.1.1 support Firmware update "on air" Supply voltage: 8 - 32VDC, 2Watt - purchase PSU Dimensions: 109 x 65 x 32 mm Weight: 152g
Multi-Network Output Module with Galvanic I / O
10/100 Mbit Ethernet Connection
Password Protected WEB Server
2 Analog Outputs with Voltage and Power Generator
0 - 20mA, 4 - 20mA, 0 - 24mA
0 - 5V or 0 - 10V voltage output
4 digital (open drain) outputs with ON / OFF or PWM
2 relays with COM, NO and NC contacts
4 scheduled actions, 1 time or weekly
NTP, SNMP v2, SNMP trap for up to 5 recipients
MODBUS TCP / IP
HTTP upload with current status in XML or JSON remote server file
HTTP API commands in server and client mode
HTTP Post can be sent to 3 servers
DIN rail / wall mounting
Supply voltage: 10 - 32VDC / max 250mA
Multi-band 4G LTE Cat.1 controller, logger and alarm Setup via USB, SMS and HTTP API USB setup - use USB cable with Mini B male 2 digital "dry contacts". High on contact 2 analog inputs, 0 - 10VDC or 4-20mA input (10bit) 4 relay outputs, COM, NO and NC 1-Wire input for up to 8 Teracom sensors 1 x RS485 for max. 8 MODBUS RTU sensors Data logger with 70,000 logs Upload data to HTTP/HTTPS Post in XML/JSON SMS alarm and Email alarm to 5 recipients Push mode – XML data is sent via HTTP Post to a remote server. Responses from server may contain relay setup. 10 to 28VDC, 370mA @ 12VDC - additional PSU Dimensions: 158 x 119 x 34 mm Weight: 470g Temperature: -20 - +55°C
Multi input data logging for up to 70000 login
10/100 Mbit Ethernet
Password protected, web-based configuration and control
4 digital inputs, compatible with S0 pulse interface
6 analog inputs with 0 / 10V and 0 / 20ma
Modbus RTU interface for up to 24 sensors (registers)
Up to 24 channels for monitoring
Up to 24 Independent Alarms
SNMP V.2 Support - SNMP Trap - Alarm Alerts
HTTP and SNMP port change - HTTP API commands
Periodic HTTP post of XML / JSON Status files for client server systems
Modbus TCP / IP support
Dynamic DNS with dynns, no- IP and DNS-O-MATIC Support
NTP protocol support
supply voltage: 10 to 32V DC
Global 4G LTE Controller, logger and alarm Supports all LTE frequencies Setup via USB, SMS and HTTP API USB setup - use USB cable with Mini B male 2 digital "dry contacts". High on contact 2 analog inputs, 0 - 10VDC or 4-20mA input (10bit) 4 relay outputs, COM, NO and NC 1-Wire input for up to 8 Teracom sensors 1 x RS485 for max. 8 MODBUS RTU sensors Data logger with 70,000 logs Upload data to HTTP/HTTPS Post in XML/JSON SMS alarm and Email alarm to 5 recipients Push mode – XML data is sent via HTTP Post to a remote server. Responses from server may contain relay setup. 10 to 28VDC, 370mA @ 12VDC - additional PSU Dimensions: 158 x 119 x 34 mm Weight: 470g Temperature: -20 - +55°C
DAQ software til TERACOM Ethernet baserede måleenheder Brugervenlig WEB interface for nem konfigurering og kontrol Fleksible bruger adgang og management Distribueret monitorering af måleenheder i “client” mode Alarm advisering Aktivitets log Grafisk og data visning med stor visualisering Nem adgang til rå-data, tabeller, eksport in .csv format (kommasepareret) Database management Sende kommando til kontrollere in “server” og “client” mode Kommando status log