POE extender, up to 100 meters, RJ45
Power over Ethernet - No Additional Power Source Required
Extend a POE signal max. 100m over a single CAT cable (cat 5 or higher)
PoE - Power over Ethernet
PoE supply voltage for clients via network cables as separate power supplies for example. surveillance cameras and serielportservere is unnecessary. PoE equipment is designed to receive the supply voltage via network cables. Often PoE also be supplied from an independent power supply. Cable lengths can restrict the use of PoE. A new standard called PoE Plus (IEEE 802.3at) can deliver more power than the...
PoE - Power over Ethernet
PoE supply voltage for clients via network cables as separate power supplies for example. surveillance cameras and serielportservere is unnecessary. PoE equipment is designed to receive the supply voltage via network cables. Often PoE also be supplied from an independent power supply. Cable lengths can restrict the use of PoE. A new standard called PoE Plus (IEEE 802.3at) can deliver more power than the current PoE standard (IEEE 802.3af). Further information about PoE is available at https://www.danbit.dk/da/content/41-hvad-er-poe-
General info about midspan and endspan
PoE standard IEEE 802.3af allows the use of two types of power supply units: endspan and midspan. < p> A endspan unit (PoE switch) typically supplies power via the data leading wires of the network cables (pins 3 and 6, 1 and 2) and is available for 10 / 100Mbit and 10/100 / Ethernet 1000Mbit sources. A endspan unit is a combined midspan injector and switch. It is installed in place of an ordinary switch, if the connected network devices to be powered over the network
A midspan injector (hub) installed between a non PoE switch and the power consuming device. It is restricted to supply power through the unused pin pair (4, 5, 7 and 8) in a 10 / 100Mbit network.
There are 45 products.
Power over Ethernet - No Additional Power Source Required
Extend a POE signal max. 100m over a single CAT cable (cat 5 or higher)
For harsh industrial and outdoor environments.
Voltage over Ethernet - PoE - no external voltage source
Extend a PoE voltage and data signal up to 100m
PoE output power: up to 22Watt
Over a single CAT 6 cable (STP cables are recommended).
Cascade: Maximum 4 ETH-BOOST-POE-1G-U units in extension
Extends the distance up to 500m
IP66
PoE+ Injector via Ethernet cable, 30Watt
Anit interference protected
OVERLOAD and monitor protected
Network: 10/100 / 1000Mbps
RJ45 Pin Assignment: 1/2 (-), 3/6 (+)
Power Supply: 100 - 240Vac
Passive PoE / POC injector for all voltages
Max. Power is 1amp
Voltage up to 48VDC
for UTP and STP Patch Cables
PoE Out: + on Pin 4, 5. - On Pin 7, 8
100Mbit Pin 1, 2, 3, 6
Plastic cabinet
Dim: 75 x 28 x 22 mm
Compact design
Output 54VDC vlotage for PoE device use
Space for PoE switch / PoE Surge protector installation
IP66 rated
Include Thermal Switch control heater and blower
Include fiber panel for fiber cable connection
Battery protection for deep discharge and short circuit
Space for 12V/7Ah Battery x 4PCS
95W input
2 x 33W output
2 x RJ45 Gigabit ethernet (10/100/1000)
10K Jumb frames
1M Packet Buffer
8K MAC address table
Surge protection
Metal cabinet & nbsp; with IP67 density
9% - 95% humidity
-40°C ~ 75°C working temperature
With wall mount
Waterproof Outdoor PoE+ Injector 30Watt
1 x RJ45 Data
1 x RJ45 Data and PoE+
1 x 2-pin DC Phoenix connectors
IK10 Vandal safe
Supply voltage: 24 - 56VDC
POE Standard: IEEE 802.3 at / af
End-Span
Pin: (+ 1.2) (- 3.6)
Operating temperature: -40 - +75°C
wall mounting
Size: 170 x 73 x 44 mm
Weight: 340g
IP67 and IK10 Gbit PoE injector for outdoor mounting
PoE++ (60W) injector for PoE equipment
1 x RJ45 port for PoE++ out Data+PoE
1 x RJ45 port Data in
1 x Phoenix connector for the input voltage
DC24V 72W input
DC36V 71W input
DC54V 66W input
PoE standard: IEEE 802.3at/bt (PoE++)
PoE out Mid-span / End-span
Operating temperature: -40 - +75°C
Wall bracket
Dimensions: 170 x 73 x 44 mm
Weight: 425
Gigabit PoE splitter for indoor mounting
PoE++ (60W) Splitter with optional DC output to non-PoE equipment
DC output: 12VDC / 5A or 19VDC / 3.2A or 24VDC / 2.5A
1 x RJ45 port to PoE++ in from Switch or PoE injector
1 x RJ45 port (data) to non-PoE equipment
1 x DC Jack connector (5.5 / 2.5mm) for equipment
POE Standard: IEEE 802.3 at / bt (PoE++)
IEEE 802.3at (PoE+ Mid-Span)
IEEE 802-3bt (PoE++ Poh HDbaset)
Operating temperature: 0 - +50°C
Wall bracket
Size: 94 x 70 x 39 mm
Weight: 265g
PoE adapter
DC injector / splitter cable
Supports 5/12/24 / 48V
Range: Up to 40m
Dimensions DC plug: 5.5 / 2.1mm
Length cable : 15cm
Set of 2 pcs. cables - injector and splitter
POE INJECTOR via Ethernet cable, 60 watts
anit interference protected
Overload and supervise protected
Network: 10/100 / 1000Mbps
RJ45 Pin Assignment: 1/2, 7/8 (- ), 3/6, 4/5 (+)
Power Supply: 100 - 240vac
Measure: 168 x 74 x 44 mm
Built 100-240V AC power supply
POC - Power Over Cable power
Meets NOT PoE specifications.
Constant voltage out.
2 x RJ45 ports - data input and data + voltage output
output voltage: DC 48V 0.5A
DC output: + (4.5) - (7.8)
Data: 1,2,3,6
Dimensions: 82 x 44 x 55 mm ( LxWxH)
Weight: 104g
4 x 10/100/1G/2.5G/5GBASE-T Gbit RJ45 data input
4 x 10/100/1G/2.5G/5GBASE-T Gbit RJ45 data + PoE output
100~240VAC, 3.33Amp PSU with DC 52V~54V power output
Complies with 802.3bt PoE Plus Plus end-span and mid-span PSE
Backward compatible with IEEE 802.3at PoE Plus end-span/mid-span PSE
Up to 4 IEEE 802.3at/IEEE 802.3bt PoE devices powered
4 x PoE ports with 90-watt 802.3bt PoE++ type 4 PSE or 95-watt PoH PoE injector function
4 x PoE ports support 802.3at end-span/mid-span PoE+ 36-watt injector function
DIP switch for 802.3bt, PoH and Force mode selection
Auto detects if devices can be PoE powered (PD)
Circuit protection prevents power interference between ports
Forwards both Ethernet data and PoE power to remote device over a 100-meter distance
EEE 802.3 Ethernet, IEEE 802.3u Fast Ethernet., IEEE 802.3ab Gigabit Ethernet
IEEE 802.3bz 2.5G/5GBASE-T, IEEE 802.3af Power over Ethernet, IEEE 802.3at Power over Ethernet Plus
IEEE 802.3bt Power over Ethernet Plus Plus
Dimensions: 94 x 70.3 x 39.2 mm
Weight: 275g
Enclosure: Metal case
4 x RJ45 port with PoE ++ (Ultra PoE)
1 x RJ 45 Uplink port (not PoE).
60W for every PoE-Port
Power Budget is 120 watts
IEEE 802.3at / by PoE.
Dip on / off PoE
Power supply: 100 - 240VAC
Operating temperature: 0 - +40°C
Size: 119 x 88 x 27 mm
Weight: 1.3 kg
Connect switches without PoE for PoE PSE to Equipment
IEEE 802.3bt back compatible to IEEE 802.3at
Supports 10/100 / 1000Mbit speeds
4 x LAN input from the switch without PoE
4 x LAN with up to 95 Watt PoE
Max. PoE power total is 240Watt (PoE power budget)
Auto-detect devices with PoE input for not destroying not PoE
Supply voltage: 48 - 54VDC max. 244 Watt
Setting with DIP switches
DIN bracket for wall mounting and
Operating temperature: -40 - +75°C
Dimensions: 135 x 88 x 50 mm
Weight: 537g
LAN without PoE voltage gives LAN with PoE
4 port PoE power supply 30 Watt per port
Connects between non-PoE switch and e.g. IP cameras with PoE
For 10/100/1000Mbit networks
Power supply included
Can be powered with 52-56VDC / 122Watt
Pin 4/5 +, 7/8 - (Mid-span)
Dimensions: 97 x 70 x 26 mm
Temp: -10 - +70°C
Built 100-240V AC power supply
POC - Power Over Cable power
Meets NOT PoE specifications.
Constant voltage out.
2 x RJ45 ports - data input and data + voltage output
output voltage: DC 24V 1A
DC output: + (4.5) - (7.8)
Data: 1,2,3,6
Dimensions: 82 x 44 x 55 mm (LxWxH )
Weight: 104g
24-ports PoE strømforsyning 30 W, 10/100 Mbit
24 ports PoE strømforsyning med 15,4 Watt per port
LAN uden PoE ind, giver LAN med PoE ud
Til 10/100Mbit netværk
Switches without PoE can with this Injector "upgraded" to PoE switch
24 ports PoE full power supply
Per port DC 52V 30.8/15.4 watts
LAN without PoE in, LAN with PoE out
10 / 100 / 1000Mbit network
Max PoE 440 Watts