Converter / Amplifier / Insulator

Get a RS485 or RS422 or RS232 port on the PC via the USB port
Galvanic isolation (optical) 2KV
DB9 male and screw terminal to 232/422/485 connection
Termination by Jumpers
Baud rate 300bit / s two 921.6 kbit / s
selectable RS232, RS422 and RS485 via DIP switch
Supports Win7 / 8/10 and over as well as MAC
Powered through USB (5V)
Operating Temp . 0 ° to 55 ° C,

USB-32COM-RM - 32-Port RS-232 USB-to-Serial Adapter, Metal Case, Rack-Mountable.

• High speed
• 128 byte transmit FIFO & 384 byte receive FIFO
• Serial port protected with surge protection of 10KV
• Built-in switching power supply of 100V~240V
• Standard 19-inch, 1U rackmount chassis

Repeater and splits an RS485 signal into 4 branches
RS485 master on input polls RS485 slaves with ID
Only asked RS485 slave responds only to master
No RS485 slave can poll the RS485 bus
2-wire RS485 - semi-duplex
Extend the star bus with more M485-REP4-I
Supply: 10 - +30VDC
Temp: -25 - +75°C
For DIN-Rail mounting

RS-422 Serial to Fiber Media Converter

RS485 & nbsp; recoverable RS232 controller / converter
Link to 3 x RS232 units from 1 x RS485 bus
Baud speed 300 bit/s to 115,200 bit/s
10 V DC to + 30 V DC
Dual watchdog
256 KB SRAM buffer
1 x & nbsp; RS485 address per. serial interface
Operating temperature: -25 ° to + 75 ° C
For DIN rail mounting

Supports HART Short / Long Frame
Supports Hart Burst Mode
Supports Point-to-point or Multi-Drop Hart mode
supports connection of up to 15 Hart slave devices
Allow 2 Hart Master
HC_Tool tool for module configuration and HART communication
support firmware update via Ethernet
PWR / TXRX indication LED
4KV ESD protection
built-in watchdog
Selectable 250Ω load resistance < Br> 4 Hart Channels
Support VXCOMM Technology
Built-in Web Server for Network Setting

RS232 galvanic isolator, 2500VAC
Transfers Tx, Rx, RTS and CTS
Up to 115 kbit / s
Input: DB9 female, output: DB9 male
RX, TX, ON indicator

12VDC / 100mA

RS232 for RS485 converter
Opto-insulated
Galvanic isolation between DC input and RS232 port
Supply voltage: 9 - 50VDC, 10 - 34VAC
Automatic flow control
Up to 1.2km Built-in Termination Resistance - Can be Disconnected
Screw Terminals

Bi-directional RS232 to RS422 converter
Galvanic isolation
DB9 male / 12VDC power supply included

USB to RS485 converter, isolated
1 x RS485 7-pin terminal block
1 x USB-B
Speed: 300 ~ 115200 bps
For USB 1.1 / 2.0 (High Speed)

2500 VDC isolation on RS485 side 
To DIN rail mounting
No external power supply required
Input +5 VDC from USB port
OS support WIN 98 / ME / 2000 / XP (32 / 64- bit) / Vista (32/64-bit) / 7 (32/64-bit) / 8 (32/64-bit) / 10 / Linux
Operating temp. -25 ° C ~ +75 ° C
USB cable (1.8m) included

Isoleret RS485 repeater til DIN skinne

Parallel til seriel omformer
Hastighed: 300 -19.200 bit/s
Handshake: XON / XOFF
Forsyning: Strømforsyning medfølger, 9 VAC, 400 mA
CNV-PAR232 er ikke bi-direktionel og kan derfor ikke sende meldinger fra printer til pc om evt. blækstatus, ”end of paper” m.m.

MODBUS RTU (RS232 / 422/485) equipment for Profibus DP network

MODBUS RTU slave devices are connected to the Profibus DP network

Allows PROFIBUS master access to MODBUS TCP devices
Connect MODBUS devices to a PROFIBUS network
PROFIBUS baud rate from 9.6k to 12M
MODBUS TCP 10/100
Supply voltage: 10 - 30VDC < DIN fitting

RS232-RS422/485 konverter
Hastighed: 230.4 kBit/s
RTS/CTS support
Til DIN og vægmontage
Plug-in terminal block til RS422/485

Optiskt isolerad RS232-adapter, max. 115,2 kbps, automatisk flödeskontroll, DB9-kontakt

Optoisolerede RS232 til RS422/485 konverter
3000Vdc isolation
24Vdc, 1.2W
RS-232 (DB9)
RS485 (2-Wire) eller RS422 (4-Wire)
Speed (bps): 1.200, 2.400, 4.800, 9.600,
19.2 k, 38.4 k, 57.6 k, 115.2 k
RTS control and RS-422 (switchable)

Optoisolerated RS422 / RS485 Repeater
3000vdc Glavanic isolation
2 threads RS485 is half duplex (switch-talk)
4 threads RS485 / RS422 A full duplex (both ways at the same time)
Translator from RS422 (4-wire) for RS485 (2-wire), semiduplex
automatic directional change and baud rate.

Repeater and splitter of an RS485 signal
Up to 3 branches, as a star connection
It is very IMPORTANT to avoid bus reflections.
Use M485-REP3-I if the RS485 bus is to be split out
For DIN Rail mounting

RS485 for RS232 or RS422 for RS232
optoisulated RS232 for RS422 / 485 Converter
supply voltage is isolated against RS232 page
Supply voltage is isolated against RS485 / 422 page
Automatic Baud rate control