With our wide range of different products, in this category we have converters, amplifiers, insulators. Here you will find interfaces like RS232 / 485/422, or convert from RS232 to RS485 / 422. If you need a specific solution for a larger project, call in and hear our sales department for more information.
Subcategories
There are 69 products.
RS232 Booster
MOXA Converter RS232 / RS422 / RS485 Fiber MultiMode, TCF-142-M-ST
Point-to-Point Fiber Converter RS232 / RS422 / RS485
Multi Mode 62.5 / 125 or 50 // 125my, wavelength 850nm
Power Supplied from 10 - 30VDC / 2 Watts
DIN Rail Bracket .
Up to 2km
ST plug
Serial to HART Convert
Allows 2 pcs. Hart Masters
Point-to-Point or Multi-Drop Hart Mode
Possibility of connecting 15 HART modules
Point-to-point or multi-drop HART mode
for configuration of modules
Isolated COM 1: RS-232 / 422/485
PWR / RUN / ERR INDICATION LED
Built-in Watchdog
4 kV ESD protection
Module to Can 2.0a and B
ISO 11898-2 standard
Baudrate 10Kbps for 1M bps
software for setting CAN and RS232 / 422/485
Transparency between RS-232 / 485/422 Via CAN bus
Full duplex on RS-232/422 units are not supported
CAN Bus Baud Rate Configuration
CAN Accept Filter Configuration
CAN 2.0A or 2.0B Specific Choice
RS-232 / 485/422 Baud rate and data file setting
RS-232/485/422 Respond Options
Setting: Normal or pair connection
Sæt udstyr med RS232, RS422 og RS485 interface på et Profibus system.
Measuring equipment for RS232 printer port can now be connected to a parallel port (LPT port)
Parallel printer port can now be connected to a serial port (RS232)
RS232 galvanic isolator, 3000VAC
With dual DC-DC converter, provides isolation both ways
Transmits Tx, Rx, RTS and CTS or DSR and DTR (selected)
Up to 115 kbit / s
Entrance: DB9 female, output: DB9 male
10-30VDC, screw terminal
DIN rail
Optoisolated RS-232 for RS485 converter
3kVDC isolation on RS232 from DC input
ESD protection for RS232 / 485
Baud rate 300 bit / s to 115,200 bit / s
Supports power inputs of +10 V DC to +30 V DC
Operating temperature: -25 ° to + 75 ° C
For DIN rail mounting
Industrial RS232 to 422/RS485 Serial Converter/ Repeater with 2 KV Isolation, MOXA TCC-100i
RS-232 to RS-422 conversion with RTS/CTS support
RS-232 to 2-wire or 4-wire RS-485 conversion
2 KV isolation protection (TCC-100I/TCC-100I-T)
Wall and DIN-rail mounting
Plug-in terminal block for easy RS-422/485 wiring
LED indicators for power, Tx, Rx
-20 to 60°C operating temperature
Extend the distance between PC and RS232 Equipment
Straight through network cable
RS232 serial port boost up to 1.2 km
Baud rate range: 300 - 200kbps
Supply voltage: DC9-24V (not included )
Optical isolation
isolation voltage: 2500Vrms pulse or 500 V = continuous
Dimensions: 100 mm x 50 mm x 20 mm
Weight: 350 g
RS232-RS422/RS485 konverter
Op til 115,2 kbit/s
Afstand: Op til 1,2km på RS422/485. op til 15 m på RS232
Forsyning: 9 VDC, 100mA, strømforsyning medfølger
Stik: RS232:DB25F,
RS485: Skrueterminal og RJ11
RS232 lysleder omformer m/DCE eller DTE omskifter
max baud rate 115kb / s for 56kb / s for signal RI
Up to 1.7km at 62.5um fiber cable.
Fiber Optic line multimode, 820nm
Transmitting: RxD , TxD, DTR, DSR, RTS, CTS, DCD, RI or 5x RxD, TxD
RS232 signal including DCE / DTE
Time multiplex, full duplex
RS232 DB9 male
Plug fiber ST
overvoltage (soft) protection - supply 600W / 1ms
polarity protected with diodes on DC input
optical indication (LED) red - PWR
Yellow - INPUT signal
Green - OUTPUT signal
Supply voltage 10-30VDC or 9 - 24VAC
power consumption max. 2W
Dimensions: 76 x 55 x 115 mm
With CNV232-485PW + you get an RS485 or RS422 port on the PC
Selecting RS422 or RS485 with DIL switches on the device
Super compact with DB9 female and screw terminals
Can be powered by external voltage from 9 - 12VDC / 500mA
Operating temperature: -40 - + 85 ° C
RS232 til TTL-konverter, DB9 Han inkl. kabel
RS232 til TTL-konverter, DB9 hun inkl. kabel
Mediekonverter fra seriel til optisk fiber
Point til Point transmission
RS232 eller RS422 eller RS485
Op til 40 km med single-mode
ST stik - duplex
Til 9/125my single mode fiber
Reducerer signalinterferens
Beskytter mod elektrisk interferens
Baud rate op til 921,6 kbps
Temperaturområde: -40 til+75°C
Forsyningsspænding: 12 - 48VDC
Mål: 100 x 90 x 22 mm
DIN beslag som tilbehør
Optoisoleret RS-485 repeater
2 vejs 3000 VDC isolation
ESD-beskyttelse til RS-485
Baud-hastighed 300 bit/s til 115.200 bit/s
Understøtter effektindtag på +10 V DC til +30 V DC
Driftstemperatur: -25° til +75°C
Til DIN skinne montering
Supports Baud Rate conversion
Supports Modbus RTU/ASCII protocol
Supports two masters sharing one slave port
Raw data mode for most query-response protocols
Built-in web server for easy configuration (HTTP)
Redundant power inputs: PoE (IEEE 802.3af, Class 1) and DC jack
Allows automatic RS-485 direction control
Tiny form-factor and low power consumption
Read-cache ensures faster response
Industrial RS422/RS485 Serial Converter/Repeater with 2 KV Isolation, MOXA TCC-120i
Boost serial signal to extend transmission distance
Boost RS422 or RS485 signal, or convert RS422 to RS485
2 KV optical isolation protection
15 KV serial ESD protection
Wall or DIN-rail mounting
Terminal block for easy wiring
Power input from terminal block
DIP switch setting for built-in terminator (120 ohms)
Optisk isolator med DB25 stik
RS232 - 08/07 bit
Max. 115.2 kbit / s
FTDI chip - FT232xx.
Does not work with software license dongles
With internal jumper getting + 5VDC on pin 9
1 meter USB cable
Supports Win10 < / p>
MOXA, 1-port RS-232 USB to serial adapter.
Compatible with USB 2.0 and 12 Mbps USB data rate
921.6 Kbps maximum baud rate for super fast data transfer
Drivers are provided for Windows, WinCE and Linux
DB9 male. USB2.0 with 80cm cable
LEDs for displaying USB and TxD / RxD activity
15 KV ESD protection for all serial ports
OS support: Windows 11, 10, 8.1, 8, 7, Vista, ME, and XP Windows Server 2022, 2019, 2016, 2012 R2, 2012, 2008 R2, 2008, 2003, 2000, and NT
RS232 for USB printer adapter cable
connect USB printer to PC com port
automatic baud rate
power supply included
DB9 female and USB B
Supply voltage: 5VDC 100mA
GDI printers (without own emulation) are not supported
See list of supported printers under Downloads
