Network products / Wifi / PoE / RJ45-Fiber

Residual sale

1 x set of PoE injector and splitter
Injector Input: 90-240VAC, Output: 48VDC IEEE802.3AF
Injektior Ports: C6 POWER, RJ45 Data Input, RJ45 Data + PoE Output
Splitter input: PoE 13.5-60VDC, Output: 12VDC
Splitter ports: RJ45 Data + PoE input, RJ45 Data output, 5.5 mm DC Pwer Output

External COM port over Ethernet and Internet.
RS232 seriesport via DB9 Han, or
RS422 / 485 port via screw terminal block
Power supplied from 12 - 48VDC. Has redundant DC input.
DIN mounting

AUI converter for UTP cable, external supply
1 x DB15 AUI female 10 Base-5 (AUI)
1 x RJ45 female 10 Base-T
Max cable length: 500m max per (Thick Ethernet), 100m max per UTP cable
LED: POWER, COL, LINK, TP / RCV
IEEE 802.3 10Base-T / AUI Ethernet
IEEE 802.2 10Base-T/10Base-2
FCC Class A Subpart B or Part15 Requirement

Wall outlet with RJ45 female plug
STP "shielded Twisted Pair" shielded outlet
Krone LSA puncher is used for mounting cables

RJ45 dust cap - blanking
Put into unused RJ45 port Kirke protection
flexible and fits all RJ45 ports.
Sold individually

RJ45 lock
RJ45 lock to stop accidental removal of the plug
Material: PLA (Plastic)
Dimensions: 15.5 x 13.8 x 18.3 mm

RJ45 m / f Ethernet Extension cable cat.5e 60 cm

AUI converter to UTP cable
1 x DB15 male to 10 Base-5 (AUI)
1 x RJ45 jack for 10 Base-T
Max cable length: 100m max per UTP cables
LED: POWER, COL, LINK, TP/RCV
IEEE 802.3 10Base-T/AUI Ethernet
FCC Class A Subpart B of Part15 Requirement
No need for external power supply

RJ45 Cat 5e / 6a
Wall installation to 8-conductor (8P8C)
TIA-568A / B colored Heating installation
No tools are needed, easy installation

2 Way Power Splitter / Combiner
Kan splitte radiosignalet til 2 antenner
Ofte anvendt til Panel-antenner
1 dB insertion loss

Samleled til 2 antenner i ét, 3 x N (hunstik)

Moxa Industrial Managed Switch ED6008

QR8041

ETH-POE5 bruges til at spændingsforsyne netværksudstyr via det almindelige Kat. 5/6 Ethernet-kabel.

Interfaces ARCNET with PCI
Utilizes COM20022 ARCNET controller
Enhanced software capabilities over earlier generation ARCNET controllers
Set one of 255 possible station addresses with node address switch or application software
Automatic configuration of I/O and interrupt
High-speed I/O access to the COM20022
Supports coaxial and twisted-pair cabling including EIA-485
Variable data rates up to 10 Mbps utilizing the various EIA-485 transceiver options
Suitable with all Contemporary Controls MOD HUB and AI Series active hubs
CE Mark

8-ports managed switch

Transient protection for 10 / 100Mbit Network. 4kV to ground.

Transfer PoE voltage.

2 x RJ45 female.

Ground wire is to be connected.

Transient protection for 10/100/1000 Mbit networks

10kV to ground.

2 x RJ45 female.

Ground wire should be connected. 

Transient protection for 10/100 Mbps network

4kV to ground.

2 x RJ45 female

Ground wire is to be connected.

Cyper Security VPN Router with dual WAN failover
Managed
10/100/1000Mbit
3 x RJ45 LAN
1 x RJ45 LAN / WAN
1 x WAN
1 x USB 3.0
Auto Reboot for 5 seconds
VPN tunnels: max 60
VPN throughput: max 100Mbps
Encryption: DES, 3DES, AES, AES-128/192/256
Authen: MD5 / SHA-1/256/384/512
IPSec (Host to Host) / GRE / PPTP server / L2TP / SSL
Operating temperature: -40 - + 75 ° C
Dimensions: 135 x 88 x 50 mm
Weight: 530g
Supply voltage: 9 - 48VDC, 9Watt
DIN bracket, wall mounting

Modbus over the Ethernet or Internet
MODBUS server with 1 x RS232 and 1 x 422/485
Can run Device to Device
0/100 Mbps Ethernet port, auto MDI / MDIX, 10/100 auto, 1500V magnetic insulation only on
RS485 RS232 Modbus ASCII / RTU port, 1 RS422 / 485 Modbus ASCII / RTU port, 16V / 400W TVS isolated, RS485 automatic line control
9 ~ 30VDC power input, IP30 enclosure , DIN rail mounting structure, USB port (Modbus serial port expansion and capture of memory)

PoE++ splitter - separate DC and Data
Data without PoE to equipment
DC voltage output to non-PoE device
Max. 70 Watt
Data is 10/100/1000Mbit/s
PoE 802.3at/bt
End-span + Mid-span
End-span or Mid-span
2  x RJ45 interfaces
1 x RJ45 port Data + Power input
1 x RJ45 port Data output
2 x DC output (4-pin terminal block)
DC output 12VDC or 24VDC w/DIP switch
Size: 135 x 88 x 32 mm
DIN-mount
Weight: 445g

4 port PoE pass through - 10/100/1000Mbit
1 x RJ45 PoE in (data + PoE++) - 95 Watt
Mid-span and End-span
4 x RJ45 PoE out (data + PoE+) - 30 Watt
PoE out pin: +1/2, -3/6
PoE output power, total is max. 75 Watt
PoE input voltage 50 - 57VDC
Temperature: -40 - +75°C
Dimensions: 135 x 88 x 32 mm
Your bracket

10/100/1000Mbit network extender / PoE splitter
1 x PoE input (PD) PoE++ 95W
4 x PoE outputs (PSE) PoE+ 32W
Up to 32W per PoE port, 65W total power budget (see specifications)
Extend the network cable over the maximum 100 meters for PoE solutions
Extenders are powered by PoE and pass PoE on to the next extender
Dimensions: 168 x 93 x 32 mm, Weight: 403g

Strømforsyning af Access Point eller webkamera via Ethernetkablet.

POE power supply via Ethernet cable, up to 30 watt
LAN without PoE in, gives LAN with PoE out
Poe +, 56VDC / 30W
10/100/1000Mbit network.
Power supplies from 12 -48VDC / 32W Max
Redundant Power Input via Terminal Block
Power supply not included
Dim: 135 x 87 x 32 mm
Operating temperature: -40 ~ +75°C

10/100 / 1000Mbit PoE Network Extender
Extend the network cable with PoE over the magic 100 meters
4 pieces. Extenders provide a maximum distance of 500 meters
Extenders are powered from PoE and pass PoE on to the next Extender
Dimensions: 94 x 70 x 26 mm

PoE In: Max 30.8 Watts

PoE Out: Max 26 Watts
Weight: 189g

PoE ULTRA Power Supply via Ethernet Cable, 60 Watt
Output Voltage: 50 - 57VDC 1.2Amp
Supporter Mid-span and End-span
Using the 4 x Pair for PoE voltage

Quick and Easy PoE tester
IEEE 802.3af / at
UTP Cat 5 or above
100 meters max.
Dimensions: 23 x 70.1 x 22 mm | Operating temperature: -10 ~ 60 C
weight: 20g

Splitter for PoE via Ethernet cable
LAN with PoE in, gives LAN without PoE out
12 VDC 2A or 24 VDC 1A next to other equipment

PoE splitter with voltage selector for 5, 9.12.18 Volts
Up to max. 30W
IEEE 602.3af/at(POE) IEEE 802.3 (Ethernet)
IEEE 802.3U, IEEE 802.3ab (Gigabit Ethernet)
1 x 10/100/1000 Mbit RJ45 PoE port (data + power input)
1 x 10/100/1000 Mbit RJ45 LAN port (data only)
1 x DC plug 5.5 / 2.1 mm - Output voltage (DC out)
Cat. 5E, 6 UTP
DC voltage from PoE switch or Injector 36 to 57 VDC
2 x RJ45 Note PoE does not go back to the RJ45 output - only data!
ROHS, CE, FCC (FCC Part15, Class B)

Stock clearance Sale

poe data and voltage splitter.
PoE in
switch to 5VDC or 12VDC
Max. Effect 15Watt
Speed: 10 / 100mbit RJ45

PoE surge protection for 10/100/1000Mbit networks
Supports PoE voltage 48VDC / 40Watt
Nominal discharge: 2.5kA, max. 5kA (8/20myS)
Response time: less than 1ns (nano-second)
Transmission loss: below 0.2dB
2 x RJ45 female (in / out)
Protected pin: 4/5, 7/8 (power supply + data), 1 - 8 (data)
Operating temperature: -40 - +70°C
Humidity: less than 90% rh
Dimensions: 93 x 55 x 35 mm
Weight: 73g
DIN bracket
Ground cable of more than 2.5kv must be shorter than 1 meter
Ground cable thickness: Min. 2.5 sq.mm
Ground resistance must be less than 4 ohms
Nothing can protect against a direct lightning strike

Passive PoE Injector with 12 / 19 / 24 VDC 0.7A output
From Active to Passive PoE converter
PoE input port: IEEE 802.3af/at RJ-45 STP / PD. Supplied from an active PoE switch
Passive PoE output port: non-802.3af/at RJ-45 STP / PSE. For equipment that is NOT for active PoE.

PoE injector
2 x 10/100 / 1000Mbit RJ45 (PoE)
UTP / TCP Cat.5e or over
Rugged Aluminum, IP30 protection
Maximum POE 95watts at 56VDC input
Dust temperature: -40 ° C ~ 75 ° C
humidity: 5% to 95% (Non-condensing)
Dimensions: 103.5 x 32 x 81.5 mm & nbsp;
Metal housing with IP30 density
DIN rail and Wall Mount

PoE injector
2 x 10/100 / 1000Mbit RJ45 (PoE)
UTP / TCP Cat.5e or over
Rugged Aluminum, IP30 protection
Maximum POE 95watts at 56VDC input
Operating Temperature: -40 ° C ~ 75 ° C
Humidity: 5% to 95% (Non-condensing)
Dimensions: 103.5 x 32 x 81.5 mm & nbsp;
Compliant with 95W Power over HDBaseT (PoH) Standard
Metal housing with IP30 density
DIN rail and wall bracket

PoE power supply via Ethernet cable, up to 30 watts

LAN without PoE input, provides LAN with PoE

For 10/100/1000Mbit network.

Power supply from 100 - 240VAC / 0.6A

PoE++ power supply via Ethernet cable, up to 95 Watt
LAN without PoE in, gives LAN with PoE out
PoE++ 54VDC/95W
Mid-span and End-span give 95 Watts
For 100/1000/2500/5000Mbit networks.
PoE power output DC 24V~54V input: Max. 89.5W@1m cable, Max. 75W@100m cable
PoE power output DC 12V input: Max. 60W@1m cable, Max. 52W@100m cable
Temperature range: -40 - +75°C
Dimensions: 135 x 88 x 32 mm
DIN installation
Powersupply input from 12 - 54VDC

PoE++ power supply via Ethernet cable, up to 60 Watt
LAN without PoE in, gives LAN with PoE out
PoE++ 48-53VDC/60W
Mid-span and End-span give 60Watt
For 100/1000/2500/5000Mbit networks.
Power is supplied from 48 - 54VDC
Temperature range: -40 - +75°C
Dimensions: 135 x 88 x 32 mm
DIN mount

Gigabit PoE and data Extender PoE splitter
1 x RJ45 Data + PoE ++ input
2 x RJ45 Data + PoE + outputs
Standard: IEEE 802.3bt and 802.3at
from injector to Extender up to 100 meters
from Extender to PD Devices Up to 100 meters
IP67 Aluminum Molded cabinet
Temperature range: -40 - + 75 ° C
Plug Play
Wall fittings
Size: 170 X 44 x 73 mm with cable gland

Gigabit PoE and Data Extender / splitter
1 x RJ45 data + PoE + input
2 x RJ45 data + PoE + outputs
Standard: IEEE 802.3af and 802.3at
From Injector to Extender up to 100 meters
From Extender out to PD devices up to 100 meters
Wall mounting
Plug & Play
Temperature range: 0- + 50 ° C
Dimensions: 140 x 77 x 28 mm
Weight: 234g

Power over Ethernet - No Additional Power Source Required
Extend a POE signal max. 100m over a single CAT cable (cat 5 or higher)

For harsh industrial and outdoor environments.
Voltage over Ethernet - PoE - no external voltage source
Extend a PoE voltage and data signal up to 100m
PoE output power: up to 22Watt
Over a single CAT 6 cable (STP cables are recommended).
Cascade: Maximum 4 ETH-BOOST-POE-1G-U units in extension
Extends the distance up to 500m
IP66

PoE+ Injector via Ethernet cable, 30Watt
Anit interference protected
OVERLOAD and monitor protected
Network: 10/100 / 1000Mbps
RJ45 Pin Assignment: 1/2 (-), 3/6 (+)
Power Supply: 100 - 240Vac

Mounting bracket for omni antennas, double
For 50mm pipe diameter
4 pcs. pipe clamp
2 pcs. steel braces
4 pcs. nuts and washers
2 pcs. screws for fixing the antenna

4 Port SATA PCIE Cards for each port up to 500MB / S to 4 individual ports (no raid)
Processor. Marvell 88SE9215
SATA up to 6.0 GB / S
Non-Raid

Chipset: Intel®I350AM4
PCI Express * 2.1 (5GT / s), operable in x4 slots or greater to 4 x RJ45, Cat 5e or more
10/100/1000 Mbps
VLAN filtering, PXE remote boot, IPMI pass-through
Os Support: Win 7 / Win 8 / Win 8.1 / Win 10 32/64Bit, Spain DOS, Linux, FreeBSD, Novell UnixWare / OpenUnix 8
Operating temperature: 0 ~ 55 ℃

1000 Mbps PCI-Express Net Card for SFP
Buy 1000Mbit SFP Module Single Mode or Multi Mode
Driver For: XP / 2003, Vista / 2008, Win 7, Linux 64-bit, Mac OS X
PCI Express, 1 Lane
SFP module can be 62.5/125my or 50/125my
Operating temperature: 0 - +65°C
Dim: 121.4 x 119.5 mm