RS232 / RS422 / RS485 / LPT Parallel

RS232 til TTL-konverter, DB9 hun inkl. kabel

RS232 til TTL-konverter, DB9 Han inkl. kabel

RS232 - 08/07 bit
Max. 115.2 kbit / s
FTDI chip - FT232xx.
Does not work with software license dongles
With internal jumper getting + 5VDC on pin 9
1 meter USB cable
Supports Win10 < / p>

Connect RS232/RS422/RS485 equipment to USB port
Baudrate up to 921,6 kbit/s
Select type of port by DIL switch
Supports Win7/8/10, MAC

Få 4 stk. RS232 porte på PC via USB porten

Forbind 4 x RS232 enheder til USB port
Metal kabinet og med vægmontering
Baudrate op til 115,2 kbit/s
Supporterer ikke hardware licens nøgler

Supporting Win10

Bi-directional RS232 to RS422 converter
Galvanic isolation
DB9 male / 12VDC power supply included

Optiskt isolerad RS232-adapter, max. 115,2 kbps, automatisk flödeskontroll, DB9-kontakt

Optoisolated RS232 for RS422 / 485 Converter
3000vdc isolation
Up to 1.2 km on the RS422 / RS485
1.2kbit/s to 115.2 kbit/s, automatic baud rate
DB9 female connector for RS232 Signal
Screw terminals for RS422 / 485 signals
Supply 10 to 30 VDC

4 ports multiplexer (sæt), op til 900m, med 2500V isolering

2 x RS232 / 422/485 Ports
PCI version 2.1 (32bit) - 3.3 / 5.0V
RS232: TX, RX, CTS, RTS - Optical ISO
RS422: TXD +/-, RXD + / -, RTS, CTS, GND
RS485: Data + / Data, GND
2 x DB9 male
Up to 921.6Kbps
Built-in Termination: 120 Ohm
DOS, Windows 98, NT , 2000, XP, Win7, Win8, 2003, Linux

2 x serial ports. 1 x parallel port for full length Mini PCI Express

Forlæng printerkablet op til 1000 meter

Extend serial cable up to 1600 meters, transiently protected
RS232 / V.24
Transparent data: syncronous and asyncronous
All HW and software handshakes
DB25 male and DB25 female
With screw terminal connection of serial I / O
With RJ45 connection of serial from special cable
DC9V / 2A power supply included

RS232 Rxtends up to 250 meters over RJ45 cable
Baud rate: 110 ~ 921,600, 8-bit
Use STP (shielded) patch cable - straight through
The network cable must not be connected to the patch panel
1 x 5VDC/1A - the power supply supplies both devices (PoC)
Important: If the distance is long, 2 power supplies are recommended
Important: If the network cable is of poor quality, use 2 power supplies

Measuring equipment for RS232 printer port can now be connected to a parallel port (LPT port)
Parallel printer port can now be connected to a serial port (RS232)

2 porte til RS232/422/485, med 2 KV iso., universal PCI
OS SUPPORT:
​64-bit System Intel Itanium 
AMD Athlon 64 64-bit CPU System 
Microsoft Win 9x/ME/NT, Win 2K/XP/2003, Win CE 
Linux 2.0.x / 2.2.x / 2.4.x / 2.6.x 
DOS DOS 

REMAINDER SALE

Serial card JetCard1208L
PCI - Low oh high backplane
8 x RS232
Up to Win 7 (32bit)

Allows PROFIBUS master access to MODBUS TCP devices
Connect MODBUS devices to a PROFIBUS network
PROFIBUS baud rate from 9.6k to 12M
MODBUS TCP 10/100
Supply voltage: 10 - 30VDC < DIN fitting

Mini PCI Express til SD adapter

8 pcs. External COM ports via Ethernet and Internet

Virtual-Com Port, Pair-Mode - Back to Back
Socket Modes: TCP Server / TCP Client / UDP
easy to configure
cables Not included (RJ45 for DB9)
Supports Win10 and earlier us, Linux

RS-422 Serial to Fiber Media Converter

RS232 for USB printer adapter cable
connect USB printer to PC com port
automatic baud rate 
power supply included
DB9 female and USB B
Supply voltage: 5VDC 100mA
GDI printers (without own emulation) are not supported 
See list of supported printers under Downloads

2-port RS422/485 serial device servers, MOXA NP5232I
Compact design for easy installation
Socket modes: TCP server/TCP client/UDP
Easy-to-use Windows utility for configuring multiple device servers
Supports 10/100M Ethernet
Patented ADDC® (Automatic Data Direction Control) for 2-wire and 4-wire RS-485
SNMP MIB-II for network management

Industrial RS232 to 422/RS485 Serial Converter/ Repeater with 2 KV Isolation, MOXA TCC-100i

RS-232 to RS-422 conversion with RTS/CTS support 
RS-232 to 2-wire or 4-wire RS-485 conversion 
2 KV isolation protection (TCC-100I/TCC-100I-T) 
Wall and DIN-rail mounting 
Plug-in terminal block for easy RS-422/485 wiring 
LED indicators for power, Tx, Rx 
-20 to 60°C operating temperature

2 ports Mechanical COM port switch, DB9 female / male
1 x DB9 female - I / O
2 x DB9 male - A and B
signal direction (I / O to A or B or A or B to I / O)
All 9 connections Switches
Good quality, but recommended for test use only
120 x 90 x 30mm

High-hanging (MOXA CP-132U-I V2)
Replacement for CP-132IS

Windows Windows 95/98 / ME / NT / 2000
Windows XP / 2003 / Vista / 2008/7/8 / 8.1 / 10 (x86 / x64)
Windows Server 2008 R2 / 2012/2012 R2 / 2016 (x64)
DOS, Windows Embedded CE 5.0 / 6.0, Windows XP Embedded

Linux Linux 2.4. x, 2.6.x, 3.x

Unix-like Systems QNX 6, SCO OpenServer, UnixWare 7, Solaris 10, FreeBSD

Printerdeling og "mininetværk" i Windows via printerporten.

max baud rate 115kb / s for 56kb / s for signal RI
Up to 1.7km at 62.5um fiber cable.
Fiber Optic line multimode, 820nm
Transmitting: RxD , TxD, DTR, DSR, RTS, CTS, DCD, RI or 5x RxD, TxD
RS232 signal including DCE / DTE
Time multiplex, full duplex
RS232 DB9 male 
Plug fiber ST
overvoltage (soft) protection - supply 600W / 1ms
polarity protected with diodes on DC input
optical indication (LED) red - PWR
Yellow - INPUT signal
Green - OUTPUT signal
Supply voltage 10-30VDC or 9 - 24VAC
power consumption max. 2W
Dimensions: 76 x 55 x 115 mm

2-port RS-422/485 with Surge & Isolation, Universal PCI Card Simple Type: MULTIFUNCTIONAL I/O

Sunix 8139SI

PROFIBUS TO HART Convert, Gateway
4 x HART Canals
Max. 2 pcs. HART Masters
Point-to-Point or Multi-Drop HART Mode
Possibility of connecting 15 HART modules
PWR / RUN / ERR indication LED
Built-in Watchdog
4 kV ESD Protection
Operating temperature -25-75 ℃
for DIN rail mounting

Intelligent Can For Modbus TCP / IP Converter
Supports both CAN specification 2.0A and 2.0B
Maximum transmission speed up to 1M BPS for CAN and 115.2 Kbps for RS-232 RS-485
Maximum transmission distance on CAN over 1000m (Follow the CAN specification)
7-segment LED display for module IP, RS-232 Baud rate, CAN configuration ...
Supports Web Configuration
Supports Maximum 24 Ethernet clients Connection
Modbus TCP / RTU command for reading and writing CAN message
Transparent communication between the CAN devices via Ethernet
30 Specific CAN IDs in Modbus TCP / RTU Mode
DIN mounting

Radio link for serial transfer on the 2.4GHz band
one for a (P2P) or one for more (P2M)
Range Up to 700 meters with whip-antenna
Range Improves panel antenna < Br> Serial port: RS232 or RS485
supply and COM port is with shed terminals
antenna: R/SMA female
Simple Setup with Turn and Dip Switche
2.4GHz, 16 channels
Supply 10 to 30 VDC

Moxa A53, DB9 W/ADAPTER

2-port RS-422/485
Communication speeds up to 921.6 Kbps.
2KV overvoltage protection, IEC-61000-4-5 Level 3.
1.5KV insulated protection meets IEC-60747 -5-5
16C950 UART controller
RS-422 and RS-485 auto detection and switching technology
jumper and software free.
On-chip hardware automatic flow control to guarantee nothing data loss.
15KV ESD protection for all serial signals meets IEC-61000-4-2 standard.
Plug-n-Play, I / O address and IRQ assigned by BIOS.
Certified by CE , FCC, VCCI, BSMI, RoHS and Microsoft WHQL authentication.
Support Microsoft Windows, Linux and DOS OS.

Wireless Com Port - Can Peer-to-Peer connection
IEEE 802.11 a/b/g/n
2.4 GHz, 5 GHz Dual Band
1 Port RS232 or RS422 or 2-wire RS485
Max.Baud Rate: 921.6 Kbps
Operating temperature: -40 - +85°C
with COM Port Re-Director, TestView
± 15KV IEC ESD protection
Supply voltage: 5 - 12VDC / 2W
infrastructure, Soft AP, Roaming
sWifi config Mobile App for Android

Bluetooth from PC to the adapter provides RS232 port
External antenna.
Bluetooth 2.0.
With 2 pcs. as back-to-back link
provides connection between 2 COM ports
Wireless transfer of data between serial ports
Up to 100 meters
Antenna connector is RSMA female
Setup via AT commands
Must be powered from 5 - 40VDC via screw terminal
USB mini cable to A male - for power from 5VDC
2 x screw terminal for any external power supply
Is not battery-powered
Use Putty for testing/setup
Help with setup can be purchased additionally

Parallel til seriel omformer
Hastighed: 300 -19.200 bit/s
Handshake: XON / XOFF
Forsyning: Strømforsyning medfølger, 9 VAC, 400 mA
CNV-PAR232 er ikke bi-direktionel og kan derfor ikke sende meldinger fra printer til pc om evt. blækstatus, ”end of paper” m.m.

Two 16550 High performance UART (RS232) serial channels
Occupies one PCI or PCIe bus slot
Low Profile PCI Form Factor
Includes Low Profile PCI & Regular size PCI two brackets
Both USB A type and USB pin header connector on board to host connection
One RS232 DB9M and one RS232 10pin RJ45 serial ports on board
Includes one 10pin RJ45 – DB9M Bridge cable for 2nd DB9M port
5VDC Power output from each DB9M Port for POS device use application
2 Jumpers Individually enable / disable 5VDC output for each DM9M Port
On Board Molex mini 4Pin Power connector for sufficient DB9M 5V bus power from PC power supply
Supports 32bit/64bit Windows 7, Vista, XP, 2000, ME, 98SE

RS232 galvanic isolator, 3000VAC
With dual DC-DC converter, provides isolation both ways
Transmits Tx, Rx, RTS and CTS or DSR and DTR (selected)
Up to 115 kbit / s
Entrance: DB9 female, output: DB9 male
10-30VDC, screw terminal
DIN rail

Sæt udstyr med RS232, RS422 og RS485 interface på et Profibus system.

MODBUS RTU (RS232 / 422/485) equipment for Profibus DP network

MODBUS RTU slave devices are connected to the Profibus DP network

Optoisolerated RS422 / RS485 Repeater
3000vdc Glavanic isolation
2 threads RS485 is half duplex (switch-talk)
4 threads RS485 / RS422 A full duplex (both ways at the same time)
Translator from RS422 (4-wire) for RS485 (2-wire), semiduplex
automatic directional change and baud rate.

USB to Hart Bus Converter
to HART Short / Long Frame
to Hart Burst Mode
Point-to-point or Multi-Drop Hart mode
Up to 15 HART slave units < Br> Allow 2 Hart Master
Module Configuration Tools and HART communication
Power supplied by the USB port
Selectable 250Ω load resistance

Serial to USB converter with 1 x RS232/422/485 port
Respects the +/- 11 volt data signals
Galvanically isolated on the RSxxx output
Self-tuner Baud Rate
Automatic direction control
Powered from the USB port
USB connector: Type B
Supports USB 1.1, 2.0 and 3.0
COM port: terminal block

4 ports multiplexer (sæt), op til 900m

PCI Express parallel card with 1. DB25 port
Most drivers up to Win10 available in the Download

Isoleret RS485 repeater til DIN skinne

2 x RS232 serial ports with plug & amp; play
1 x TITAN BSP9216B (chipset)
1 x DB25 male connector on the card
1 x DB25 female for two DB9 male adapter cables included
Bus: universal PCI (5V and 3.3V) 32 bit 33MHz
RS232 signal: DCD, RxD, TxD, DTR, GND, DSR, RTS, CTS, RI
Max. bitrate: 921.6kbps
Each port with 16 bit FIFO for transmit & amp; review
IS support: Windows, Linux
0 ° C to 60 ° C

RS232 lysleder omformer m/DCE eller DTE omskifter

1 meters kabel til SER8PCI-K+ med 8 x DB9

Get a COM port on the Android Tablet or Android phone via USB port

Connect 1 x RS232 equipment to Android Tablet / phone
Connect to micro USB port on the Tablet / Phone
Baud rate up to 921.6 kbit / s

Supports HART Short / Long Frame
Supports Hart Burst Mode
Supports Point-to-point or Multi-Drop Hart mode
supports connection of up to 15 Hart slave devices
Allow 2 Hart Master
HC_Tool tool for module configuration and HART communication
support firmware update via Ethernet
PWR / TXRX indication LED
4KV ESD protection
built-in watchdog
Selectable 250Ω load resistance < Br> 4 Hart Channels
Support VXCOMM Technology
Built-in Web Server for Network Setting

• PCI Express x 1, 2x RS232, RS422/485
• RS485 ART (Automatic Receive Transmit control), RS485 in 3 operation modes
• optical isolation, surge protection (also in RS232), Compact board size (half-size)
• Built-in termination resistors

UHF 433 MHz RS-232 adapter

RS-232 konfigureres via COM port

1 to 1 tilslutning

1 to N broadcast 

Op til 200 meter

MOXA 

4 x RS485/422 COM ports over fiber, fiber network
Extender over fiber with 4 x RS422 / 485
1 x 100 Mbit fiber
Screw terminal block (5 pole)
SFP slot for 100mbit Multi Mode LC Fiber
62 x 50 x 120 mm
Display 3 LEDs Displays TX / RX, Network and System Status
Supply 9 - 32 VDC (not supplied)

MOXA USB to RS422/485 converter
Galvanically isolated.
1-port RS-422/485 USB-to-serial converter
Compatible with USB 2.0
12 Mbps USB data rate
921.6 kbps maximum baud rate for super fast data transmission
Drivers provided for Windows, Windows Server, WinCE, and Linux
Mini DB9 female to terminal block adapter for easy wiring
LEDs for indicating USB and TxD/RxD activity
15 kV ESD protection for all serial ports
2 kV electrical isolation
Supports Windows 11

Serielportserver 2 x RS232 / 422 /485 MOXA Nport 5210
Compact design for easy installation
Socket modes: TCP server/TCP client/UDP
Easy-to-use Windows utility for configuring multiple device servers
Supports 10/100M Ethernet
Patented ADDC® (Automatic Data Direction Control) for 2-wire and 4-wire RS-485
SNMP MIB-II for network management

Moxa:

Auto Data Switch MP401B Parallel Printer Sharing Device
4 PCs can share the same parallel printer
Automatic switch to parallel printer
Active line is displayed with LED
Timeout programmable from 3 to 70 sec.
Supplied with 9VDC voltage supply
Plug: 5 pcs. DB25 female connector

2-port RS-422/485 high speed communication board
Windows 2000 / XP / 2003, Windows NT, Windows 95/98 / ME, WIN 7, WIN 8, WIN 10 32/64 Bit
Windows XP Embedded, WINDOWS 2003, 2008, 2012
DOS, FreeBSD 4.x, Linux 2.0.x (Alpha), Linux 2.2.x (Alpha), Linux Base

MOXA CP132I

Internet Communication controller with 1 x CAN bus, 1 x RS-232, 1 x RS-485 and 1 x Ethernet
10/100 Base-TX Ethernet controller
TCP / IP protocol
80 MHz CPU
1 x RS-232 port, 1 x RS-485 port and 1X CAN port can be used simultaneously
Max Transmission Speed ​​up to 1M BPS for CAN and 115.2Kbps for RS-232 RS-485
7 -Segment LED Display
Software Configuration for Can and RS-232
Web Configuration
Up to 25 Ethernet Client Connections
Supports Virtual Com

1 Ports LTE Serial for Ethernet Gateway / Modem, RS232 / 422/485

GSM / GPRS / EDGE / UMTS / HSPA / LTE
Supports VPN and virtual computing
operating temperature 0- 55 ° C
IP30
12-48 VDC
DIN mounting (fittings included)

High-speed USB to RS232/422/485 adapter
Transmission speed - up to 921.6 kbps
Supports USB 1.2/2.0/3.0
3000V DC isolation on RS232/422/485
RS232/422/485 cannot be used simultaneously
Supplied via the USB port
Automatic RS485 Direction Control
Temperature range: -25°C - +75°C
DIN rail mounting
Windows 98/ME/2000/XP/Vista (32/64-bit)
Windows 7 / 8.1 / 10 (32/64-bit)
Win 2012
Linux

USB-C - Serial RS232 Adapter cable
USB Type C Han to 9-pole RS-232 Han connector with finger screws
Download speed 1 Mbps +
Supports Remote Wake-up and Power MM
1.8 meters

Extend the distance between PC and RS232 Equipment
Straight through network cable
RS232 serial port boost up to 1.2 km
Baud rate range: 300 - 200kbps
Supply voltage: DC9-24V (not included )
Optical isolation
isolation voltage: 2500Vrms pulse or 500 V = continuous
Dimensions: 100 mm x 50 mm x 20 mm
Weight: 350 g

2 COM ports over Ethernet, Internet
Each COM port can be RS232 or RS422 or RS485
RS232 Pin 1 - 8: DCD, RXD, TXD, DTR, GND, DSR, RTS, CTS
RS422 / RS485 4-W: Pin 1 - 5: TXD +, TXD, RXD +, RXD, GND
RS485 2-W: Pin 3 - 5: Data, Data +, GND
Baud Rate: 50 bps - 921Kbps
Data Bits: 5, 6, 7, 8
Parity: 1, 1.5, 2
Stop Bit: Odd, Even, None, Space, Mark
2 x RJ45 10 / 100mbit
Alarm: Relay output
Supply voltage: 12 - 48VDC 6.5WATT
Web Management
IP Version: IPv4 / IPv6. TCP Server, TCP Client, UDP Client
Virtual Com
Pair Connection
Supporter: XP to Win10, Server 2003, 2008, 2012
Size: 135 x 88 x 32 mm
DIN bracket

Module to Can 2.0a and B
ISO 11898-2 standard
Baudrate 10Kbps for 1M bps
software for setting CAN and RS232 / 422/485
Transparency between RS-232 / 485/422 Via CAN bus
Full duplex on RS-232/422 units are not supported
CAN Bus Baud Rate Configuration
CAN Accept Filter Configuration
CAN 2.0A or 2.0B Specific Choice
RS-232 / 485/422 Baud rate and data file setting
RS-232/485/422 Respond Options
Setting: Normal or pair connection

Supports Baud Rate conversion
Supports Modbus RTU/ASCII protocol
Supports two masters sharing one slave port
Raw data mode for most query-response protocols
Built-in web server for easy configuration (HTTP)
Redundant power inputs: PoE (IEEE 802.3af, Class 1) and DC jack
Allows automatic RS-485 direction control
Tiny form-factor and low power consumption
Read-cache ensures faster response

Extends serial cables up to 1600 meters or printer cables up to 180 meters.

RS232 galvanic isolator, 2500VAC
Transfers Tx, Rx, RTS and CTS
Up to 115 kbit / s
Input: DB9 female, output: DB9 male
RX, TX, ON indicator

12VDC / 100mA

External COM port over Ethernet and Internet.
RS232 seriesport via DB9 Han, or
RS422 / 485 port via screw terminal block
Power supplied from 12 - 48VDC. Has redundant DC input.
DIN mounting

RS485 for RS232 or RS422 for RS232
optoisulated RS232 for RS422 / 485 Converter
supply voltage is isolated against RS232 page
Supply voltage is isolated against RS485 / 422 page
Automatic Baud rate control

Repeater and splits an RS485 signal into 4 branches
RS485 master on input polls RS485 slaves with ID
Only asked RS485 slave responds only to master
No RS485 slave can poll the RS485 bus
2-wire RS485 - semi-duplex
Extend the star bus with more M485-REP4-I
Supply: 10 - +30VDC
Temp: -25 - +75°C
For DIN-Rail mounting

2 RS422/485 serielle porte til PCI Express