Network products / Wifi / PoE / RJ45-Fiber

10/100/1000Mbit network extender / PoE splitter
1 x PoE input (PD) PoE++ 95W
4 x PoE outputs (PSE) PoE+ 32W
Up to 32W per PoE port, 65W total power budget (see specifications)
Extend the network cable over the maximum 100 meters for PoE solutions
Extenders are powered by PoE and pass PoE on to the next extender
Dimensions: 168 x 93 x 32 mm, Weight: 403g

Strømforsyning af Access Point eller webkamera via Ethernetkablet.

POE power supply via Ethernet cable, up to 30 watt
LAN without PoE in, gives LAN with PoE out
Poe +, 56VDC / 30W
10/100/1000Mbit network.
Power supplies from 12 -48VDC / 32W Max
Redundant Power Input via Terminal Block
Power supply not included
Dim: 135 x 87 x 32 mm
Operating temperature: -40 ~ +75°C

10/100 / 1000Mbit PoE Network Extender
Extend the network cable with PoE over the magic 100 meters
4 pieces. Extenders provide a maximum distance of 500 meters
Extenders are powered from PoE and pass PoE on to the next Extender
Dimensions: 94 x 70 x 26 mm

PoE In: Max 30.8 Watts

PoE Out: Max 26 Watts
Weight: 189g

PoE ULTRA Power Supply via Ethernet Cable, 60 Watt
Output Voltage: 50 - 57VDC 1.2Amp
Supporter Mid-span and End-span
Using the 4 x Pair for PoE voltage

Quick and Easy PoE tester
IEEE 802.3af / at
UTP Cat 5 or above
100 meters max.
Dimensions: 23 x 70.1 x 22 mm | Operating temperature: -10 ~ 60 C
weight: 20g

Splitter for PoE via Ethernet cable
LAN with PoE in, gives LAN without PoE out
12 VDC 2A or 24 VDC 1A next to other equipment

PoE splitter with voltage selector for 5, 9.12.18 Volts
Up to max. 30W
IEEE 602.3af/at(POE) IEEE 802.3 (Ethernet)
IEEE 802.3U, IEEE 802.3ab (Gigabit Ethernet)
1 x 10/100/1000 Mbit RJ45 PoE port (data + power input)
1 x 10/100/1000 Mbit RJ45 LAN port (data only)
1 x DC plug 5.5 / 2.1 mm - Output voltage (DC out)
Cat. 5E, 6 UTP
DC voltage from PoE switch or Injector 36 to 57 VDC
2 x RJ45 Note PoE does not go back to the RJ45 output - only data!
ROHS, CE, FCC (FCC Part15, Class B)

Stock clearance Sale

poe data and voltage splitter.
PoE in
switch to 5VDC or 12VDC
Max. Effect 15Watt
Speed: 10 / 100mbit RJ45

PoE surge protection for 10/100/1000Mbit networks
Supports PoE voltage 48VDC / 40Watt
Nominal discharge: 2.5kA, max. 5kA (8/20myS)
Response time: less than 1ns (nano-second)
Transmission loss: below 0.2dB
2 x RJ45 female (in / out)
Protected pin: 4/5, 7/8 (power supply + data), 1 - 8 (data)
Operating temperature: -40 - +70°C
Humidity: less than 90% rh
Dimensions: 93 x 55 x 35 mm
Weight: 73g
DIN bracket
Ground cable of more than 2.5kv must be shorter than 1 meter
Ground cable thickness: Min. 2.5 sq.mm
Ground resistance must be less than 4 ohms
Nothing can protect against a direct lightning strike

Passive PoE Injector with 12 / 19 / 24 VDC 0.7A output
From Active to Passive PoE converter
PoE input port: IEEE 802.3af/at RJ-45 STP / PD. Supplied from an active PoE switch
Passive PoE output port: non-802.3af/at RJ-45 STP / PSE. For equipment that is NOT for active PoE.

PoE injector
2 x 10/100 / 1000Mbit RJ45 (PoE)
UTP / TCP Cat.5e or over
Rugged Aluminum, IP30 protection
Maximum POE 95watts at 56VDC input
Dust temperature: -40 ° C ~ 75 ° C
humidity: 5% to 95% (Non-condensing)
Dimensions: 103.5 x 32 x 81.5 mm & nbsp;
Metal housing with IP30 density
DIN rail and Wall Mount

PoE injector
2 x 10/100 / 1000Mbit RJ45 (PoE)
UTP / TCP Cat.5e or over
Rugged Aluminum, IP30 protection
Maximum POE 95watts at 56VDC input
Operating Temperature: -40 ° C ~ 75 ° C
Humidity: 5% to 95% (Non-condensing)
Dimensions: 103.5 x 32 x 81.5 mm & nbsp;
Compliant with 95W Power over HDBaseT (PoH) Standard
Metal housing with IP30 density
DIN rail and wall bracket

PoE power supply via Ethernet cable, up to 30 watts

LAN without PoE input, provides LAN with PoE

For 10/100/1000Mbit network.

Power supply from 100 - 240VAC / 0.6A

PoE++ power supply via Ethernet cable, up to 95 Watt
LAN without PoE in, gives LAN with PoE out
PoE++ 54VDC/95W
Mid-span and End-span give 95 Watts
For 100/1000/2500/5000Mbit networks.
PoE power output DC 24V~54V input: Max. 89.5W@1m cable, Max. 75W@100m cable
PoE power output DC 12V input: Max. 60W@1m cable, Max. 52W@100m cable
Temperature range: -40 - +75°C
Dimensions: 135 x 88 x 32 mm
DIN installation
Powersupply input from 12 - 54VDC

PoE++ power supply via Ethernet cable, up to 60 Watt
LAN without PoE in, gives LAN with PoE out
PoE++ 48-53VDC/60W
Mid-span and End-span give 60Watt
For 100/1000/2500/5000Mbit networks.
Power is supplied from 48 - 54VDC
Temperature range: -40 - +75°C
Dimensions: 135 x 88 x 32 mm
DIN mount

Gigabit PoE and data Extender PoE splitter
1 x RJ45 Data + PoE ++ input
2 x RJ45 Data + PoE + outputs
Standard: IEEE 802.3bt and 802.3at
from injector to Extender up to 100 meters
from Extender to PD Devices Up to 100 meters
IP67 Aluminum Molded cabinet
Temperature range: -40 - + 75 ° C
Plug Play
Wall fittings
Size: 170 X 44 x 73 mm with cable gland

Gigabit PoE and Data Extender / splitter
1 x RJ45 data + PoE + input
2 x RJ45 data + PoE + outputs
Standard: IEEE 802.3af and 802.3at
From Injector to Extender up to 100 meters
From Extender out to PD devices up to 100 meters
Wall mounting
Plug & Play
Temperature range: 0- + 50 ° C
Dimensions: 140 x 77 x 28 mm
Weight: 234g

Power over Ethernet - No Additional Power Source Required
Extend a POE signal max. 100m over a single CAT cable (cat 5 or higher)

For harsh industrial and outdoor environments.
Voltage over Ethernet - PoE - no external voltage source
Extend a PoE voltage and data signal up to 100m
PoE output power: up to 22Watt
Over a single CAT 6 cable (STP cables are recommended).
Cascade: Maximum 4 ETH-BOOST-POE-1G-U units in extension
Extends the distance up to 500m
IP66

PoE+ Injector via Ethernet cable, 30Watt
Anit interference protected
OVERLOAD and monitor protected
Network: 10/100 / 1000Mbps
RJ45 Pin Assignment: 1/2 (-), 3/6 (+)
Power Supply: 100 - 240Vac

Mounting bracket for omni antennas, double
For 50mm pipe diameter
4 pcs. pipe clamp
2 pcs. steel braces
4 pcs. nuts and washers
2 pcs. screws for fixing the antenna

4 Port SATA PCIE Cards for each port up to 500MB / S to 4 individual ports (no raid)
Processor. Marvell 88SE9215
SATA up to 6.0 GB / S
Non-Raid

Chipset: Intel®I350AM4
PCI Express * 2.1 (5GT / s), operable in x4 slots or greater to 4 x RJ45, Cat 5e or more
10/100/1000 Mbps
VLAN filtering, PXE remote boot, IPMI pass-through
Os Support: Win 7 / Win 8 / Win 8.1 / Win 10 32/64Bit, Spain DOS, Linux, FreeBSD, Novell UnixWare / OpenUnix 8
Operating temperature: 0 ~ 55 ℃

1000 Mbps PCI-Express Net Card for SFP
Buy 1000Mbit SFP Module Single Mode or Multi Mode
Driver For: XP / 2003, Vista / 2008, Win 7, Linux 64-bit, Mac OS X
PCI Express, 1 Lane
SFP module can be 62.5/125my or 50/125my
Operating temperature: 0 - +65°C
Dim: 121.4 x 119.5 mm

Cipset: WCH384L
maximum rate: 1.5 Mbps to 4 x RS-232 serial expansion
FIFO: 256-bytes (for each port)
data rate: 115kbps (for each port)
OS support: Windows 98SE / ME / NT 4. 0 / Server 2000
XP / Vista / Server 2003 / Win 7 / Win 8 / Win 10, DOS, Linux

2 Ports SFP PCI Express
10 gigabit ethernet
Interface: SFP fiber optic
Chipset: Intel 82599ES
OS Support: Win 7/8 / 8.1 / 10 / DOS / Linux
Power consumption: 5.5W
Certificates: FCC, CE, RoHS
Operating temperature: 0-55 degrees

Compliant with Serial ATA 3.0
Marvel 88SE9230 processor to 4 x internal SATA connector
communication speed: 6/3 / 1.5 Gbit
Raid 0, 1, 10, Hyper duo
OS support : windoes XP / vista / server03 / server08 / win7 / 8/10 / dos / linux
Mirror data from SSD mechanical hard drives for databeskyttelske

Intel 82576EB
PCI Express v2.0 (2.5GT / s), X 4, or x8 operable in x16 slots
RJ45 (copper)
10/100/1000 Mbps
IMPI pass-through , PXE remote boot, VLAN filtering
OS support: Win 7 / Win 8 / Win 8.1 / Win 10 3264Bit
3.6W
Operating Temperature: 0 ~ 55 ℃

Passive PoE / POC injector for all voltages
Max. Power is 1amp
Voltage up to 48VDC
for UTP and STP Patch Cables
PoE Out: + on Pin 4, 5. - On Pin 7, 8
100Mbit Pin 1, 2, 3, 6
Plastic cabinet
Dim: 75 x 28 x 22 mm

Demo Item - Without Packaging or Accessories
Korenix Jetnet 5010g
7 x 10/100 RJ45 Ethernet
3 x 10/100/1000 RJ45 Ethernet / SFP Combo Ports (10/100 / 1000 Base- T, 100 base-eg, 1000 base-x)
supply voltage: 10.5 ~ 60 VDC
Operating temperature: -25 ~ 70 ° C

WiFi booster 1W, 11/54 for outdoor use

2-way Wifi amplifier. NOTE: maximum radiated power must be 100 mW

NOTE: Cable not included

Vandal secure GSM dome dome antenna for hollow mounting
Quad band - 850/900/1800/1900 / 2170MHz
With 2.5 meters RG 174U cable - SMA he
ABS plastic - with rubber seal Ø47 x 15mm, M10 thread, 12mm
bandwidth ± 90/280 MHz
Gain 2,5dBi
vertical
Max wind speed 200km/h

Compact design
Output 54VDC vlotage for PoE device use
Space for PoE switch / PoE Surge protector installation
IP66 rated
Include Thermal Switch control heater and blower
Include fiber panel for fiber cable connection
Battery protection for deep discharge and short circuit
Space for 12V/7Ah Battery x 4PCS

Wireless WIFI 3G / 4G Router.
Built-directional antenna to 3G/4G.
Built-in WiFi antennas.
2 x cable entry IP tight.
2 x LAN 10/100/1000 Mbps Ethernet
Power supply: 12V ~ 24V Passive PoE (POC)
18VDC / 1A Passive PoE adapter included
Downlink of 150 Mbps Uplink of 50Mbps
Mast clamp / wall
Temperature: -30 ° ~ +70°C

Outdoor 4G router with Wifi
802.11b/g/n/ac dual band 2.4 / 5GHz WPA2
AP, Client, Station, Bridge Mode Support
VPN: IPSec, PPTP / L2TP, GRE, OpenVPN
Cat 6 LTE - UL: 300Mbps, DL: 50Mbps
IP67
Power Supply: 12VDC 1.5A PoC (adapter included)
PoC is power over Cable (network cable)
2 x N type male to 4G (antennas included)
2 x N type male to WiFi (antennas included)
Mounting kit for Pole

Outdoor 4G router with Wifi
802.11b/g/n/ac dual band 2.4 / 5GHz WPA2
AP, Client, Station, Bridge Mode Support
VPN: IPSec, PPTP / L2TP, GRE, OpenVPN
Cat 4 LTE - UL: 150Mbps, DL: 50Mbps
IP67
Power Supply: 12VDC 1.5A PoC (adapter included)
PoC is power over Cable (network cable)
2 x N type male to 4G (antennas included)
2 x N type male to WiFi (antennas included)
Mounting kit for pole

Outdoor 4G router with Wifi
802.11b/g/n/ac dual band 2.4 / 5GHz WPA2
AP, Client, Station, Bridge Mode Support
VPN: IPSec, PPTP / L2TP, GRE, OpenVPN
Cat 12 LTE - UL: 600Mbps, DL: 150Mbps
IP67
Power Supply: 12VDC 1.5A PoC (adapter included)
PoC is power over Cable (network cable)
2 x N type male to 4G (antennas included)
2 x N type male to WiFi (antennas included)
Mounting kit for Pole

Single-Use RJ45 port lock in plastic to ensure network ports
Physical blockage of port
mounted and dismounted without tools
Serial number on each lock for identification and security

Ethernet through the same phase of electric cables - sold as a set (2 pcs.)

Not suitable for industrial use.

Integrated 10/100/1000 transceiver
Auto-Negotiation with Next Page capability
Supports PCI rev.2.3, 32-bit, 33/66MHz
Supports pair swap/polarity/skew correction
Crossover Detection & Auto-Correction
Wake-on-LAN and remote wake-up support
Microsoft® NDIS5 Checksum Offload (IP, TCP, UDP) and largesend offload support
Supports Full Duplex flow control (IEEE 802.3x)
Fully compatible with IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
Supports IEEE 802.1P Layer 2 Priority Encoding
Supports IEEE 802.1Q VLAN tagging
Serial EEPROM
3.3/1.8/1.5V signaling, 5V PCI I/O tolerant
0.15µm CMOS process
Transmit/Receive FIFO (8K/64K) support
Supports power down/link down power saving
Supports PCI Message Signaled Interrupt (MSI)

1000 Mbit/s netkort til lysleder m. SC stik 3,3 V PCI, 64 bit

10 Gbit PCI-Express netkort med SFP+

100 Mbit PCI-Express Fiber Card with LC connector Low Profile

Antenna adapter
exterior thread + hole (N type)
exterior thread + pin (RP-TNC)
Impedance: 50 ohm

Connect Multimode fiber network with single mode fiber network
1 x 100Mbit Single Mode SC
1 x 100Mbit Multimode SC
Wavelength: 1310 / 1310nm
100Base-SX / LX fiber network
5VDC / 2A adapter included

For the interconnection of single mode and multimode fiber networks
1000Base-SX to 1000Base-LX, SM, 850/1310 nm
only to Gigabit fiber networks.

Please note this product is EOL and of older vintage. We only recommend it to users who have experience with old analogue model/telephone technology.

If you don't have experience with the older technology, don't jump into it, that's our recommendation.

MPCIE WLAN modul
fra 2.412 til 2.462 GHz
802.11b/g
Power output 177 mW

Beslag til montage af WiFi antenner

Beslag / kit fastmontering af panel antenner

Sælges inkl. skruer i et sæt med 2 stk. kit

Rustfri stål

Beslag til montage af  WiFi antenner

Modular design for easy replacement
Supports 10M/100M/1G/2.5Gbps Ethernet
Supports 802.3af / 802.3at / 802.3bt / UPoE
Protects 8 wires of network cable, including PoE
Protects Up to 20KV / 10KA wave
Error indicator LED
Operating temperature from -40°C to 85°C
DIN rail mounting

LTE Cat 4 module
51.0 mm × 30.0 mm × 4.9 mm
Max. 150 Mbps downlink / 50 Mbps uplink under LTE
Mini PCIe form factor
Temperature range of -35°C to +75°C
OS support Windows7/8/8.1/10/11, Linux, Android
Note: without SIM card holder

12 mini slots media converter box / casing
1U rack mounting | 1/10 / 1000M
Dimensions: 485 (W) x 270 (D) x 44.5 (H)
Operating temperature: 0- 50

100Mbit fiber media converter to RJ45, Single Mode
1 x RJ45 10 / 100Mbit | 1 x SC 100Mbit Singlemode
1310nm
up to 35 km

1000Mbit Multimode Media Converter for RJ45
1 x RJ45 10/100 / 1000BaseT
1 x 1000BaseSX / LX with SC connector Multimode
Back-Pressure in Half-Duplex
Auto MDI / MDI -X function in Store-and-forward mechanism
Up to 220m / 550m
Dimensions: 97 x 70 x 26 mm
Operating temperature: 0 - + 50 ° C
Power supply: 5VDC / 2A included

1 x 10/100/1000Mbit RJ45
1 x 1000Mbit SFP (only for Gigabit SFP modules)
up to 80km with Single Mode fiber
up to 550m with Multi Mode fiber
The SFP module is standard for LC connectors, duplex, Single Mode / Multi Mode.
BIDI with LC or with SC (Simplex fiber)
Purchase additional Gigabit SFP modules.
up to 100m with Cat.5e or Cat.6
5% to 95% humidity
5VDC power supply included
-0°C to +70°C

10/100/1000Base-TX til 1000Base-LX, 1550 nm, Single Mode, 50 km
Kun til 1000Mbit fiber, Single Mode

100/1000Mbit fiber media converter RJ45
1 x RJ45 10/100/1000Mbit BASE-T
1 x SFP slot 100 / 1000Mbit BASE-X dual mode
Supports WDM SFP modules (Bi-Directional data 1 on fiber) 
WDM SFP module have wavelengths 1310nm and 1550nm
IEEE 802.3 / 802.3u / 802.3ab / 802.3z
IP30 metal housing
DIN rail and wall mounting design
Supply voltage: 12VDC to 48VDC polarity protected
AC supply voltage: 24VAC / 50Hz
PSU not included 
Operating temperature: -40°C to +75°C

100 / 1000Mbit Media Converter with extended temperature
1 x RJ45 10/100 / 1000BASE-T
1 x SFP slot 100 / 1000Mbit
SFP module is as standard for LC connectors, duplex, Single Mode / Multi Mode.
Purchase 100Mbit / Gigabit SFP modules.
Supply voltage: 9 - 48VDC redundant power
Can also be connected to 24VAC
consumption: 2Watt
Power not supplied
Dimensions: 104 x 70 x 30 mm
IP30 metal housing
DIN rail and wall mounting
Weight: 251G
operating temperature -40 to +75°C

1000Mbit Multi Mode Media Converter with SC connector to RJ45
1000BASE-SX / LX to 10/100/1000BASE-T 802.3at PoE
1 x RJ45 10/100/1000base-T with PoE+ (30W)
1 x 1000base-SX/LX Fiber - SC connector Multi Mode
Multi Mode 62.5/125my / 50/125my
IEEE 802.3/802.3u/802.3ab/802.3z/802.3x Ethernet standard
DIN rail mounting
Supply voltages: 12 - 48VDC or 24VAC with PoE out
PSU not included
IP30
Operating temperature: -40°C to +75°C

10/100/1000Base-TX to 1000Base-LX
1310 nm, Single Mode
Up to 10 km
Uses singlemode fiber cable (9/125 µm)
Only for 1000Mbit fiber, Single Mode

Media converter 1000Mbit Multi Mode SC duplex, 550 meters
10/100/1000Base-TX to 1000Base-SX, 850 nm
Multi Mode fiber cable (50/125 µm or 62.5/125 µm)

Media Converter 100Mbit Multimode ST duplex - 2km
1 x RJ45 10 / 100Mbit
1 x ST 100Mbit
1310nm
5VDC
Dimensions: 97 x 69 x 26 mm

Replaced by ETH-RJ45G-SFP2

1000Mbit Media converter can connect 2 different fiber networks and RJ45
Is suitable as a node in Gigabit fiber networks with 1 x RJ45
1 x RJ45 10/100/1000Mbit
2 x 1000Mbit SFP slot for SFP modules Single Mode and/or Multi Mode
Can also connect Single Mode networks with Multi Mode networks
The SFP module is standard for LC connectors, duplex, Single Mode / Multi Mode.
Purchase additional Gigabit SFP modules.
5VDC power supply included

1 x 10/100 / 1000BASE-T RJ45 IEEE 802.3bt PoE ++ output
2 x SFP slot 1000BASE-X and 100BASE-FX TC-dual mode
PoE Power up to 95 watts to PoE port
Provides 54VDC of the RJ45 Ethernet cable for devices with Ethernet PoE port
Automatic detection of IEEE 802.3bt-equipment United Protects devices from being damaged by incorrect installation
Remove Power supply up to 100 meters
IEEE 802.3af / at / bt splitter devices compatible
Layer 2 features
DIP switch: Selecting the standard / Legacy mode
IP30 metal housing
DIN rail and wall mounting
12 - 56V DC redundant power with reverse polarity protection
power supply not included
Operating Temperature -40 to 75 ° C,

WDN media converter for 1-core fiber, Singlemode SC.
1 x RJ45 10/100 / 1000Base-TX | 1 x 1-core (simples) single mode fiber with SC
Must be used with ETH-RJ45G-WDM SA
Up to 15 km
WDM wavelenght-division-multiplexing - only for simplex fiber cable
Must be WDM converter at both ends of the fiber

10/100 / 1000Base-TX for 1000Base-LX single mode, 15km
WDM wavelength-division-multiplexing - Simplex fiber cable only
Must be WDM convert at both ends of the fiber.

Media Converter for 10Gbit Fiber
1 x RJ45 10Gbit/5Gbit/2.5Gbit/1Gbit/100Mbit Base-T
1 x 10GBase-X SFP+ Slot
For 50/125my and 62.5/125my, Single Mode or Multi Mode
SFP Module is by default for LC connectors, Duplex, Single Mode / Multi Mode.
Purchase SFP Module
Supply voltage: 5VDC
Power supply included
Operating temperature 0 to +50°C
Dimensions: 94 x 70 x 26 mm

1 x 10/100 / 1000Mbit RJ45
1 x 100 / 1000Mbit SFP
SFP module is as standard for LC connectors, duplex, Single Mode / Multi Mode.
Purchase 100Mbit / Gigabit SFP modules.
POE (PSE) up to 95W
48-56 VDC
IP30 rated
-40 ° C to + 75 ° C
5% to 95% humidity
DIN bracket

IP67 sealed media converter, ideal for Camcorder, AP etc.
1 port 1000Mbit fiber SFP slot
SFP slot for Single Mode or Multi Mode optical transceiver
1 port 100/100/1000Mbit RJ45
Autodetection of PD equipment (devices that must be powered by PoE)
PoE+ out: 30Watt
End-span: + on 1/2, - on 3/6
IK10 rated for vandal protection
6kV ESD protection
Supply voltage: 24 - 56VDC (Terminal block)
Temperature range: -40 - +75°C
Plug and Play
Dimensions: 170 x 44 x 73 mm
Wall mounting

Media converter for 100Mbit Multi Mode Fiber SC
RJ45 10/100Mbit
Fiber 100Mbit 62.5/125my and 50/125my
-40 to +75°C
12 - 48 VDC Redundant PSU input

10Gbit fiber the RJ45 Media converter
For Single Mode or Multi Mode SFP module
Extended temperature range
1 x RJ45 10G/5G/2.5G/1G/100M BASE-T
1 x 10GBASE-SR/LR SFP slot
The SFP module is standard with an LC connector
Additional SFP module
Supply voltage: 12 - 48VDC
PSU not included
Operating temperature -40 to +75°C
YOUR bracket

DIN-mounted super compact media converter
100 Mbit fiber (additional purchase SFP module)
RJ45 10/100 Mbit
Ideal for installation in camera housings or where space is tight
The SFP module is standard for LC connectors, duplex, Single Mode / Multi Mode
SFP modules - see under Accessories
Supply voltage: 12 - 60VDC or 18 - 36 VAC
Temperature range: -40° - +75° C
5% to 95% humidity
36 x 59 x 49mm (H x W x D)
DIN bracket included