Network products / Wifi / PoE / RJ45-Fiber

Serial device server with RS232 / RS485

RS232 via DB9

RS485 via screw terminal - 2-wire

POE power supply via Ethernet cable, up to 30 watt
LAN without PoE in, gives LAN with PoE out
Poe +, 56VDC / 30W
10/100/1000Mbit network.
Power supplies from 12 -48VDC / 32W Max
Redundant Power Input via Terminal Block
Power supply not included
Dim: 135 x 87 x 32 mm
Operating temperature: -40 ~ +75°C

WDN media converter for 1-core fiber, Singlemode SC.
1 x RJ45 10/100 / 1000Base-TX | 1 x 1-core (simples) single mode fiber with SC
Must be used with ETH-RJ45G-WDM SA
Up to 15 km
WDM wavelenght-division-multiplexing - only for simplex fiber cable
Must be WDM converter at both ends of the fiber

Transient protection for 10 / 100Mbit Network. 4kV to ground.

Transfer PoE voltage.

2 x RJ45 female.

Ground wire is to be connected.

Directional antenna - yagi type
9 dBi outdoor logperiodisk
20 cm coaxial cable with N-type he
two bands 800-960 / 1700-2500MHz
Mast bracket with angle adjustment included

Unmanaged 6 ports industriswitch
6 x RJ45 10/100Mbit
Redundant PSU input.

Intel 82576EB
PCI Express v2.0 (2.5GT / s), X 4, or x8 operable in x16 slots
RJ45 (copper)
10/100/1000 Mbps
IMPI pass-through , PXE remote boot, VLAN filtering
OS support: Win 7 / Win 8 / Win 8.1 / Win 10 3264Bit
3.6W
Operating Temperature: 0 ~ 55 ℃

PoE ULTRA Power Supply via Ethernet Cable, 60 Watt
Output Voltage: 50 - 57VDC 1.2Amp
Supporter Mid-span and End-span
Using the 4 x Pair for PoE voltage

Bluetooth from PC to the adapter provides RS232 port
External antenna.
Bluetooth 2.0.
With 2 pcs. as back-to-back link
provides connection between 2 COM ports
Wireless transfer of data between serial ports
Up to 100 meters
Antenna connector is RSMA female
Setup via AT commands
Must be powered from 5 - 40VDC via screw terminal
USB mini cable to A male - for power from 5VDC
2 x screw terminal for any external power supply
Is not battery-powered
Use Putty for testing/setup
Help with setup can be purchased additionally

Gigabit PoE and Data Extender / splitter
1 x RJ45 data + PoE + input
2 x RJ45 data + PoE + outputs
Standard: IEEE 802.3af and 802.3at
From Injector to Extender up to 100 meters
From Extender out to PD devices up to 100 meters
Wall mounting
Plug & Play
Temperature range: 0- + 50 ° C
Dimensions: 140 x 77 x 28 mm
Weight: 234g

High Speed Access Point - Dual Band
AP, Repeater, Bridge, Bridge to several
Up to 64 simultaneous users
2.4GHz, 5GHz
Transmission: aggregated up to 1200 Mbps
Transmit power: 500mW - adjustable
2 x 5dBi antennas - removable with good range
Ports: 1 x 10/100Mbps RJ45 WAN port
IP67 tight
Powered via passive PoE or supplied 24VDC adapter
Power consumption: less than 12 Watts
Dimensions: 380 x Ø54 mm
Temperature: -40 - +55°C

Vandal-proof and waterproof dome antenna
The LTE band 700-2700MHz (including GSM, 3G and 4G)
VSWR: <=1.5
Passive gain: 7-8 dBi
Polarization: Vertical
Nominal power: 50W
Input impedance: 50 Ohm
Cable length: 1.5 meters
Cable type: RG174
Connector type: SMA male
Weight of antenna: 57g
360° Omnidirectional
Center hole mounting

5 Ports & nbsp; Switch with 4 PoE ports
4 x PoE RJ45
1 x Uplink RJ45
1 x SFP
Ethernet standard: IEEE802.3, IEEE 802.3u, IEEE802.3af / at
Power Supply: DC48V - 52V

Unmanaged 8 ports industriswitch 
8 x 10/100Mbit med RJ45
IP50-tæt - metalkabinet
9 - 48VDC, 3,15Watt - Redundancy PSU input

Media converter for 100Mbit Multi Mode Fiber SC
RJ45 10/100Mbit
Fiber 100Mbit 62.5/125my and 50/125my
-40 to +75°C
12 - 48 VDC Redundant PSU input

Unmanaged 8 ports 10/100/1000Mbit switch
1.5Mbits SRAM packet buffer
IP30 metal case
DIN rail and wall-mount
-40 to 75 degrees C operating temperature
12 to 48V DC input (power supply is not included)

External COM port via Ethernet and Internet
RS232 Serialport via DB9 male
Power supplied from PoE
can be powered from 12 - 48VDC / 1.7 watts
Short Power Jack Pigtail Cable included
Purchase Power supply, not included
1 x RJ45 with PoE input
DIN mount
Operating temperature: -25 - + 75 ° C
Dim: 90 x 52 x 27 mm

MiniGBIC / SFP+
LC
1310 nm
up to 10 km, single-mode

LAN interface til termisk bonprinter

100/1000Mbit fiber media converter RJ45
1 x RJ45 10/100/1000Mbit BASE-T
1 x SFP slot 100 / 1000Mbit BASE-X dual mode
Supports WDM SFP modules (Bi-Directional data 1 on fiber) 
WDM SFP module have wavelengths 1310nm and 1550nm
IEEE 802.3 / 802.3u / 802.3ab / 802.3z
IP30 metal housing
DIN rail and wall mounting design
Supply voltage: 12VDC to 48VDC polarity protected
AC supply voltage: 24VAC / 50Hz
PSU not included 
Operating temperature: -40°C to +75°C

100 / 1000Mbit Media Converter with extended temperature
1 x RJ45 10/100 / 1000BASE-T
1 x SFP slot 100 / 1000Mbit
SFP module is as standard for LC connectors, duplex, Single Mode / Multi Mode.
Purchase 100Mbit / Gigabit SFP modules.
Supply voltage: 9 - 48VDC redundant power
Can also be connected to 24VAC
consumption: 2Watt
Power not supplied
Dimensions: 104 x 70 x 30 mm
IP30 metal housing
DIN rail and wall mounting
Weight: 251G
operating temperature -40 to +75°C

LAN without PoE voltage gives LAN with PoE
4 port PoE power supply 30 Watt per port
Connects between non-PoE switch and e.g. IP cameras with PoE
For 10/100/1000Mbit networks
Power supply included
Can be powered with 52-56VDC / 122Watt
Pin 4/5 +, 7/8 - (Mid-span)
Dimensions: 97 x 70 x 26 mm
Temp: -10 - +70°C

2.5Gbit single core WDM optisk transceiver
Single Mode Wavelength-Division-Multiplexing
Mini GBIC - small form factor
Til simplex fiber (enkelt core) med LC stik
Estimeret rækkevidde er 20km
Driftstemperatur: -40 - +70°C
Tilkøb modpart som monteres i anden ende af fibren
CNV-SFP2.5G-WDM-B 

Unmanaged 5 port Ethernet switch
5 x 10/100/1000Mbit, RJ45
Operating temperature: -40 - +70 °C
10 - 30VDC

Udendørs 2,4GHz rundstråleantenne 15 dBi
Vertikal spredning er 6 grader
Horisontal spredning er 360 grader
N hun stik
Højde 1,6meter
Mastebeslag medfølger

Use VDSL connection over 2-thread cable where WiFi is an unstable connection

up to 1.4 km above eg. Conducted phone cable with 2 pcs. VDSL modules
Use 2 pcs. ETH-VDSL2+4+ or ETH-VDSL2+A and ETH-VDSL2+4+
Ethernet over 2-wire connection with VDSL
Ideal solution When the network distance is over 100 meters of border
ideal solution when a WiFi Link is an unstable connection
providing a transparent data connection
supply: 5VDC, 2A power supply included
DIP switch: VDSL connection must be set to CPE and the other for CO.
Prepared for your Montage, wall assembly. Your fittings are purchased
Order 2 pcs for a set.

2 pieces. VDSL2 + A can be established network connection over the 2-wire cable

Up to 1.4 Km Ethernet bridge via the 2 pieces. VDSL2 + A
speed depends on cable and length - up to 90Mbps
Automatically adapts speed to highest speed
can also communicate with ETH-VDSL2 + 4 + (4 port switch)
1 x LAN 10/100 BASE-T RJ45 auto-MDI / MDI-X port
1 x VDSL2 + A RJ11 she
supply: 5VDC, 2A power supply included
By 2 pcs. ETH-VDSL2 + A one shall be put to the CPE and the other to CO.
Connect each end of the 2-wire twisted pair cable.
ESD protection: 6KV DC Kirke DIN mounting, wall mounting. Your hardware purchased
SOLD SEPARATELY! Order 2 pieces for one set.

Transparent Ethernet connection up to 1200 meters
Medium range from 11 - 80Mbps up to 1200 meters
Long range from 14 - 89Mbps up to 700 meters
Range is dependant on cable quality etc.
1 x RJ45 for LAN
1 x RJ45 for Link (RJ11 can also fit into the female plug
DIP Switch to select Master or Slave mode
Dimensions: 97 x 70 x 26 mm
Cabinet: Metal
Weight: 189g
Supply voltage: 5VDC/2A
Temperature: 0 - +50°C

ZigBee modul med 8 indgange

Master, 200bit buffer

10/100/1000Mbit network extender / PoE splitter
1 x PoE input (PD) PoE++ 95W
4 x PoE outputs (PSE) PoE+ 32W
Up to 32W per PoE port, 65W total power budget (see specifications)
Extend the network cable over the maximum 100 meters for PoE solutions
Extenders are powered by PoE and pass PoE on to the next extender
Dimensions: 168 x 93 x 32 mm, Weight: 403g

Unmanaged 5 Ports IndustriSwitch
4 x RJ45 10 / 100mbit
1 x SC Fiber 100Mbit Single Mode
IP30

2 Ports Poe Injector provides 2 x 36Watt for PD equipment
10/100/1000 Mbit
pin 4/5 (+), pin 7/8 (-)
4 x RJ45 (2 with data and 2 with data + PoE for equipment)
supply voltage: 12 - 56VDC
Power Budget is 60 - 72 Watt
Dim: 105 x 70 x 30 watts
Weight: 280g
Operating temperature: -40 - + 75 ° C
DIN mounting

5 x 10 / 100TX Ports with Auto MDI / MDI-X
Good size for industrial use
18-32VDC
relay port alerting
Support AC 1.5KV Hi-pot isolation protection IP31 Aluminum
Operating temperature: -25 to 70 degrees
Dimensions: 111.8mm (H) x 30mm (W) x 98.2mm (D)
Weight: 290g box without

5GHz, 900Mbps AP, Gateway, Repeater, Bridge, WISP
802.11 b/g/n/ac
2T2R architecture with dual-polarizing 14dBi antennas built-in
Transmission power: 100mW
2 x 10/100/1000Mbps RJ45 Ethernet
For pipe mounting and wall mounting - clamping band included
Supports WAN connection in DHCP, Static IP, PPPoE
WPA/WPA2, WPA-PSK/WPA2-PSK and 802.1X RADIUS authentication
IP55
Power supply: PoE+ (48Vdc) or 12VDC 1A (via DC jack)
Operating temperature: -20 - +70°C
Dimensions: 260 x 87 x 38 mm

Device server til multimode fiber med RS232/422/485 serieport

IP67 and IK10 Gbit PoE injector for outdoor mounting
PoE++ (60W) injector for PoE equipment
1 x RJ45 port for PoE++ out Data+PoE
1 x RJ45 port Data in
1 x Phoenix connector for the input voltage
DC24V 72W input
DC36V 71W input
DC54V 66W input
PoE standard: IEEE 802.3at/bt (PoE++)
PoE out Mid-span / End-span
Operating temperature: -40 - +75°C
Wall bracket
Dimensions: 170 x 73 x 44 mm
Weight: 425

Break the 100 meter limit with VDSL over RG59 coax cable
1 x RJ45 10/100 Mbit
Up to 94 Mbit/s - duplex (automatic speed optimization)
Transparent (untouched) data connection
128-bit AES encryption
Frequencies: 2 - 28MHz
Same device can be Master or Slave (DIP)
Establishes even the best connection
Dimensions: 97 x 70 x 26 mm
Temperature: 0-50°C
5VDC 2A power supply included
75Ω cable must be used
Use 2 pcs. ETH-VDSL-RG for a point to point connection
Use 1 pc. Master for 4 pcs. Slaves - 1:4

Gigabit PoE splitter for indoor mounting
PoE++ (60W) Splitter with optional DC output to non-PoE equipment
DC output: 12VDC / 5A or 19VDC / 3.2A or 24VDC / 2.5A
1 x RJ45 port to PoE++ in from Switch or PoE injector
1 x RJ45 port (data) to non-PoE equipment
1 x DC Jack connector (5.5 / 2.5mm) for equipment
POE Standard: IEEE 802.3 at / bt (PoE++)
IEEE 802.3at (PoE+ Mid-Span)
IEEE 802-3bt (PoE++ Poh HDbaset)
Operating temperature: 0 - +50°C
Wall bracket
Size: 94 x 70 x 39 mm
Weight: 265g

Outdoor directional parabola antenna 19dBi
Vertical spread is 7 degrees
Horizontal spread is 8 degrees
Mast bracket - adjustable - included
N she stick
1070 x 610mm

Waterproof Outdoor PoE+ Injector 30Watt
1 x RJ45 Data
1 x RJ45 Data and PoE+
1 x 2-pin DC Phoenix connectors
IK10 Vandal safe
Supply voltage: 24 - 56VDC
POE Standard: IEEE 802.3 at / af
End-Span
Pin: (+ 1.2) (- 3.6)
Operating temperature: -40 - +75°C
wall mounting
Size: 170 x 73 x 44 mm
Weight: 340g

ZigBee modul med 14 indgange

ZigBee module with 6 inputs and 4 relay outputs

7 DBI outdoor Omni antenna with N-type female socket
Horizontal: 360 degrees
Vertical: 9 degrees at ½ power
700-900 / 1800-2170 / 2300-2690MHz
Length is 76cm
n She connector
for mounting on pipes
for mounting on wall
Wind resistant Over 250km / h
Weight: 400g
Max. Effect: 50W
Impredance: 50 Ohm
mounting brackets included
glass fiber, copper inside, stainless steel Feature

Unmanaged 5 ports industriswitch
4 x RJ45 10/100Mbit
1 x ST fiber 100Mbit Multi Mode
IP50

24 ports 10/100/1000Mbit non managed Ethernet switch - 48Gbit/s.
100 - 240VAC PSU indbygget
Metalchassis. 
Rackbeslag medfølger.

Media converter for 100/1000Base-X SFP transceiver
The SFP module is standard for LC connectors, duplex, Single Mode / Multi Mode.
Purchase 100Mbit / Gigabit SFP modules.
10/100/1000Base-TX
24V / 48V DC power input for PoE
Supply voltage can be 24VAC
Mid-span PoE (PSE) (4.5/7.8)
PoE power out is max. 30 Watt
Alarm in case of link failure
For DIN rail mounting

WiFi Booster 500mW, 11/54 for indoor use

2-way WiFi amplifier. NOTE: max. Radiated power may be 100 mW

AT Commands Communication
Bandwidth 1.4/3/5/10/15/20MHz
LTE-FDD：B1/B3/B7/B8/B20/B28A
WCDMA：B1/B8
GSM：B3/B8
Input DC 8V-28V
working temperature -30℃-70℃
Dimensions 82 × 84 × 24mm
Max upstream rate 50Mbps
Max downstream rate 150Mbps
RS485/RS232

Directional antenna - Yagi Type
2 bands 800-960 / 1700-2500MHz
angle: Horizontal 65 °, Vertical 55 °
11 DBI Outdoor logperiodisk
20 cm COAX cable with N- Type He
Dim: 446 x 210 x 65 mm
Weight: 900g
Max. Wind speed: 60 m / second
DC Ground - Transient Protection
Material: ABS
Masters with angle adjustment included

IEEE 802.3AT / by POE standard compatible
Compatible with all IEEE 802.3AT / by PoE units
56VDC 50pwatt POE power
divides 56V DC power over RJ-45 to 12VDC or 19VDC or 24VDC
External power supply up to 100 meters

Replaced by ETH-RJ45G-SFP2

1000Mbit Media converter can connect 2 different fiber networks and RJ45
Is suitable as a node in Gigabit fiber networks with 1 x RJ45
1 x RJ45 10/100/1000Mbit
2 x 1000Mbit SFP slot for SFP modules Single Mode and/or Multi Mode
Can also connect Single Mode networks with Multi Mode networks
The SFP module is standard for LC connectors, duplex, Single Mode / Multi Mode.
Purchase additional Gigabit SFP modules.
5VDC power supply included

Samleled til 2 antenner i ét, 3 x N (hunstik)

Unmanaged 8 ports industry switch & nbsp;
8 x 10/100 / 1000Mbit with RJ45
IP30 -Set metal housing
9 - 48VDC, 4Watt - Redundancy PSU input

External COM ports via Ethernet and Internet
3-in-1 Serial Port: RS-232, RS-422, OR RS-485
Modes: TCP Server, TCP Client, UDP
Ethernet Modem
Pair Connection
Real Com / Tty Drivers for Windows and Linux
2-wire RS-485 with Patented Automatic Data Direction Control (Addc®)
Built-in 15 kV ESD Protection for All Serial Signal

AUI converter for BNC cable, external supply
1 x DB15 Han to 10 Base-5 (AUI)
1 x BNC Jack for 10 Base-2
Max. Cable length: 500m thick coax, 182m thin coax
LED: Power, COL, LINK, TP / RCV
IEEE 802.3 10Base-5/2 Ethernet
0 to 55 ° C
10 to 90% ( Non-condensing)

MiniGBIC / SFP+
10 Gigabit
LC
850 nm
Up to 300 m multimode

External COM port over Ethernet and Internet.
RS232 seriesport via DB9 Han, or
RS422 / 485 port via screw terminal block
Power supplied from 12 - 48VDC. Has redundant DC input.
DIN mounting

External COM port via Ethernet and Internet
RS422 / 485 Serial port via screw terminal
Power supplied from POE or 12 - 48VDC
Your mounting

Unmanaged 5 port 10/100/1000Mbit
Redundant power input
9 - 48VDC
24 VAC

For harsh industrial and outdoor environments.
Voltage over Ethernet - PoE - no external voltage source
Extend a PoE voltage and data signal up to 100m
PoE output power: up to 22Watt
Over a single CAT 6 cable (STP cables are recommended).
Cascade: Maximum 4 ETH-BOOST-POE-1G-U units in extension
Extends the distance up to 500m
IP66

54 Mbit access point med PoE, udendørs

Rest storage

Vdsl2 router with 4 x RJ45 and WiFi
Network connection up to 1.4 km above 2-wire telephone cables
point to point federal
2 pcs. Eth-VDSL2ROUTER for a connection

Media converter for 100/1000Base-X SFP transceiver
The SFP module is standard for LC connectors, duplex, Single Mode / Multi Mode.
Purchase additional Gigabit SFP modules.
1 x RJ45 10/100/1000Base-TX PoE+
1 x SFP 100/1000 Mbit
Power supply: 48-56VDC
PSU not included
End-span PoE (1/2(+), 3/6(-))
PoE power is max. 36 Watt
DIN rail or wall mounting
Temperature: -40 to +75°C
Dimensions: 30 x 70 x 104 mm

External COM port via Ethernet and Internet - for fiber cable
SerialportServer 1 x RS232 / 422/485
Fiber is 100Mbit SFP (Single Mode or Multi Mode)

Unmanaged 5 Ports Industriswitch
4 x RJ45 10/100Mbit
1 x St Fiber 100Mbit Multi Mode
IP40

Isolator for 1000 Mbit network, one port
Insulation on all 4 pairs.
Transient protector - Remember the earth connection (screw)
2 x RJ45 female
Max. Discharge current (fine LL): 40A (8/20 microSec)
Max. Discharge current (coarse LE): 2.5 kA (8/20 microSec)
Residual voltage: <5V (1.2/50 microSec)
Hi-Pot (Pri to Sec) isolation: 1500Vrms, 1mA, 60 seconds
Cannot transmit PoE
Dimensions: 72 x 50 x 25 mm

Unmanaged 5 ports industriswitch
4 x RJ45 10/100Mbit
1 x SC fiber 100Mbit Single Mode
IP50

PoE injector
2 x 10/100 / 1000Mbit RJ45 (PoE)
UTP / TCP Cat.5e or over
Rugged Aluminum, IP30 protection
Maximum POE 95watts at 56VDC input
Operating Temperature: -40 ° C ~ 75 ° C
Humidity: 5% to 95% (Non-condensing)
Dimensions: 103.5 x 32 x 81.5 mm & nbsp;
Compliant with 95W Power over HDBaseT (PoH) Standard
Metal housing with IP30 density
DIN rail and wall bracket

4 ch Network extender over 2-wire, RJ45 or Coax cable
Provides transparent Ethernet connection up to 2000 meters
Range with up to 46Mbps: max. 1200 meters COAX
Range with up to 28Mbps: max. 1000 meters RJ11
Range with up to 73Mbps: max. 699 meters RJ45 UTP
Range depends on cable quality etc.
4 x RJ45 for LAN
1 x RJ45 for Link (RJ11 can also fit in the female connector
1 x BNC Coax 75ohm
DIP switch to select Master or Slave mode
Dimensions: 155 x 86 x 26 mm
Cabinet: Metal
Weight: 347g
Supply voltage: 12VDC/1A
Temperature: 0 - +50°C

Rest storage

2 Ports Repeater to 10 Base2 and 10 Base5 Network
BNC / Aui Ethernet
can convert between Aui and BNC networks.

External COM port via Ethernet and Internet.

1-port RS-232 serial device servers

5 ports 10/100/1000Mbps Fast Ethernet switch
Auto MDI/MDI-X Function
Store-and-Forward Switching Architecture
10Gbps Back-Plane (Switching Fabric)
8K MAC Address Table
9.6Kbytes Jumbo Frame Support
Surge Protection: 3,000 VDC
ESD Protection: 6,000 VDC
Redundant Power Input – 12~48VDC
1 Relay Output til Port Break Alarm
IP30 Aluminum kabinet
DIN-Rail og Wall Mount
Temperaturområde: -10° to 70°C

External COM port over Ethernet and Internet
RS232/422/485
Atop SE5201-DB Serial Device Server
10/100Mbit Ethernet.
Serial port via DB9 male connector
Supports TCP Server/Client, UDP, Virtual COM and Tunneling modes
Power is supplied from 9 - 30VDC or 5VDC (power jack)
Power supply not included
DIN kit (option)
Dimensions: 65 x 78 x 28mm (without wall bracket)
Dimensions: 88.5 x 84 x 27.8mm (with wall bracket and DB9 port)

Serial Device Server for RS232 / RS422 / RS485 with WiFi

Single-Use RJ45 port lock in plastic to ensure network ports
Physical blockage of port
mounted and dismounted without tools
Serial number on each lock for identification and security

1000Mbit Multimode Media Converter for RJ45
1 x RJ45 10/100 / 1000BaseT
1 x 1000BaseSX / LX with SC connector Multimode
Back-Pressure in Half-Duplex
Auto MDI / MDI -X function in Store-and-forward mechanism
Up to 220m / 550m
Dimensions: 97 x 70 x 26 mm
Operating temperature: 0 - + 50 ° C
Power supply: 5VDC / 2A included

Converter 10Base-T to 10Base-2
1 x RJ45 from Hub / Station select swich
1 x BNC to 10 Base-2
100m max. per UTP cable
185m max. Coax
12V DC, 1 Amp
0 to 55 ° C
10 to 90% (Non-Condensing)
IEEE 802.3 10Base-T / 10Base-2
Network: Star - CSMA / CD

PoE++ splitter - separate DC and Data
Data without PoE to equipment
DC voltage output to non-PoE device
Max. 70 Watt
Data is 10/100/1000Mbit/s
PoE 802.3at/bt
End-span + Mid-span
End-span or Mid-span
2  x RJ45 interfaces
1 x RJ45 port Data + Power input
1 x RJ45 port Data output
2 x DC output (4-pin terminal block)
DC output 12VDC or 24VDC w/DIP switch
Size: 135 x 88 x 32 mm
DIN-mount
Weight: 445g

PoE++ power supply via Ethernet cable, up to 60 Watt
LAN without PoE in, gives LAN with PoE out
PoE++ 48-53VDC/60W
Mid-span and End-span give 60Watt
For 100/1000/2500/5000Mbit networks.
Power is supplied from 48 - 54VDC
Temperature range: -40 - +75°C
Dimensions: 135 x 88 x 32 mm
DIN mount

Unmanaged 8 ports switch
Store-and-forward arkitektur
-40 °C - +75 °C driftstemperatur
8 x 10/100 Mbps speed auto negotiation
+10 ~ +30 VDC power input
DIN-Rail Mounting

IP67 sealed media converter, ideal for Camcorder, AP etc.
1 port 1000Mbit fiber SFP slot
SFP slot for Single Mode or Multi Mode optical transceiver
1 port 100/100/1000Mbit RJ45
Autodetection of PD equipment (devices that must be powered by PoE)
PoE+ out: 30Watt
End-span: + on 1/2, - on 3/6
IK10 rated for vandal protection
6kV ESD protection
Supply voltage: 24 - 56VDC (Terminal block)
Temperature range: -40 - +75°C
Plug and Play
Dimensions: 170 x 44 x 73 mm
Wall mounting