RS232-TTL konverter DB9 hun
RS232 til TTL-konverter, DB9 hun inkl. kabel
In this category you can find Serial / parallel ports, PCI or PCI Express cards for RS232 / 485/422. If you need a PCI card for your PC or a booster or converter up to 1 km, you can find it in this category. Serial port server, converter, amplifier, isolators, PCI cards and more. Feel free to call our sales department to inquire about a specific product.
Subcategories
RS232 til TTL-konverter, DB9 hun inkl. kabel
RS232 til TTL-konverter, DB9 Han inkl. kabel
RS232 - 08/07 bit
Max. 115.2 kbit / s
FTDI chip - FT232xx.
Does not work with software license dongles
With internal jumper getting + 5VDC on pin 9
1 meter USB cable
Supports Win10 < / p>
Connect RS232/RS422/RS485 equipment to USB port
Baudrate up to 921,6 kbit/s
Select type of port by DIL switch
Supports Win7/8/10, MAC
Få 4 stk. RS232 porte på PC via USB porten
Forbind 4 x RS232 enheder til USB port
Metal kabinet og med vægmontering
Baudrate op til 115,2 kbit/s
Supporterer ikke hardware licens nøgler
Supporting Win10
Bi-directional RS232 to RS422 converter
Galvanic isolation
DB9 male / 12VDC power supply included
Optiskt isolerad RS232-adapter, max. 115,2 kbps, automatisk flödeskontroll, DB9-kontakt
Optoisolated RS232 for RS422 / 485 Converter
3000vdc isolation
Up to 1.2 km on the RS422 / RS485
1.2kbit/s to 115.2 kbit/s, automatic baud rate
DB9 female connector for RS232 Signal
Screw terminals for RS422 / 485 signals
Supply 10 to 30 VDC
4 ports multiplexer (sæt), op til 900m, med 2500V isolering
2 x RS232 / 422/485 Ports
PCI version 2.1 (32bit) - 3.3 / 5.0V
RS232: TX, RX, CTS, RTS - Optical ISO
RS422: TXD +/-, RXD + / -, RTS, CTS, GND
RS485: Data + / Data, GND
2 x DB9 male
Up to 921.6Kbps
Built-in Termination: 120 Ohm
DOS, Windows 98, NT , 2000, XP, Win7, Win8, 2003, Linux
2 x serial ports. 1 x parallel port for full length Mini PCI Express
Forlæng printerkablet op til 1000 meter
Extend serial cable up to 1600 meters, transiently protected
RS232 / V.24
Transparent data: syncronous and asyncronous
All HW and software handshakes
DB25 male and DB25 female
With screw terminal connection of serial I / O
With RJ45 connection of serial from special cable
DC9V / 2A power supply included
RS232 Rxtends up to 250 meters over RJ45 cable
Baud rate: 110 ~ 921,600, 8-bit
Use STP (shielded) patch cable - straight through
The network cable must not be connected to the patch panel
1 x 5VDC/1A - the power supply supplies both devices (PoC)
Important: If the distance is long, 2 power supplies are recommended
Important: If the network cable is of poor quality, use 2 power supplies
Measuring equipment for RS232 printer port can now be connected to a parallel port (LPT port)
Parallel printer port can now be connected to a serial port (RS232)
2 porte til RS232/422/485, med 2 KV iso., universal PCI
OS SUPPORT:
64-bit System Intel Itanium
AMD Athlon 64 64-bit CPU System
Microsoft Win 9x/ME/NT, Win 2K/XP/2003, Win CE
Linux 2.0.x / 2.2.x / 2.4.x / 2.6.x
DOS DOS
REMAINDER SALE
Serial card JetCard1208L
PCI - Low oh high backplane
8 x RS232
Up to Win 7 (32bit)
Allows PROFIBUS master access to MODBUS TCP devices
Connect MODBUS devices to a PROFIBUS network
PROFIBUS baud rate from 9.6k to 12M
MODBUS TCP 10/100
Supply voltage: 10 - 30VDC < DIN fitting
Mini PCI Express til SD adapter
8 pcs. External COM ports via Ethernet and Internet
Virtual-Com Port, Pair-Mode - Back to Back
Socket Modes: TCP Server / TCP Client / UDP
easy to configure
cables Not included (RJ45 for DB9)
Supports Win10 and earlier us, Linux
RS-422 Serial to Fiber Media Converter
RS232 for USB printer adapter cable
connect USB printer to PC com port
automatic baud rate
power supply included
DB9 female and USB B
Supply voltage: 5VDC 100mA
GDI printers (without own emulation) are not supported
See list of supported printers under Downloads
2-port RS422/485 serial device servers, MOXA NP5232I
Compact design for easy installation
Socket modes: TCP server/TCP client/UDP
Easy-to-use Windows utility for configuring multiple device servers
Supports 10/100M Ethernet
Patented ADDC® (Automatic Data Direction Control) for 2-wire and 4-wire RS-485
SNMP MIB-II for network management
Industrial RS232 to 422/RS485 Serial Converter/ Repeater with 2 KV Isolation, MOXA TCC-100i
RS-232 to RS-422 conversion with RTS/CTS support
RS-232 to 2-wire or 4-wire RS-485 conversion
2 KV isolation protection (TCC-100I/TCC-100I-T)
Wall and DIN-rail mounting
Plug-in terminal block for easy RS-422/485 wiring
LED indicators for power, Tx, Rx
-20 to 60°C operating temperature
2 ports Mechanical COM port switch, DB9 female / male
1 x DB9 female - I / O
2 x DB9 male - A and B
signal direction (I / O to A or B or A or B to I / O)
All 9 connections Switches
Good quality, but recommended for test use only
120 x 90 x 30mm
High-hanging (MOXA CP-132U-I V2)
Replacement for CP-132IS
Windows Windows 95/98 / ME / NT / 2000
Windows XP / 2003 / Vista / 2008/7/8 / 8.1 / 10 (x86 / x64)
Windows Server 2008 R2 / 2012/2012 R2 / 2016 (x64)
DOS, Windows Embedded CE 5.0 / 6.0, Windows XP Embedded
Linux Linux 2.4. x, 2.6.x, 3.x
Unix-like Systems QNX 6, SCO OpenServer, UnixWare 7, Solaris 10, FreeBSD
Printerdeling og "mininetværk" i Windows via printerporten.
max baud rate 115kb / s for 56kb / s for signal RI
Up to 1.7km at 62.5um fiber cable.
Fiber Optic line multimode, 820nm
Transmitting: RxD , TxD, DTR, DSR, RTS, CTS, DCD, RI or 5x RxD, TxD
RS232 signal including DCE / DTE
Time multiplex, full duplex
RS232 DB9 male
Plug fiber ST
overvoltage (soft) protection - supply 600W / 1ms
polarity protected with diodes on DC input
optical indication (LED) red - PWR
Yellow - INPUT signal
Green - OUTPUT signal
Supply voltage 10-30VDC or 9 - 24VAC
power consumption max. 2W
Dimensions: 76 x 55 x 115 mm
2-port RS-422/485 with Surge & Isolation, Universal PCI Card Simple Type: MULTIFUNCTIONAL I/O
Sunix 8139SI
PROFIBUS TO HART Convert, Gateway
4 x HART Canals
Max. 2 pcs. HART Masters
Point-to-Point or Multi-Drop HART Mode
Possibility of connecting 15 HART modules
PWR / RUN / ERR indication LED
Built-in Watchdog
4 kV ESD Protection
Operating temperature -25-75 ℃
for DIN rail mounting
Intelligent Can For Modbus TCP / IP Converter
Supports both CAN specification 2.0A and 2.0B
Maximum transmission speed up to 1M BPS for CAN and 115.2 Kbps for RS-232 RS-485
Maximum transmission distance on CAN over 1000m (Follow the CAN specification)
7-segment LED display for module IP, RS-232 Baud rate, CAN configuration ...
Supports Web Configuration
Supports Maximum 24 Ethernet clients Connection
Modbus TCP / RTU command for reading and writing CAN message
Transparent communication between the CAN devices via Ethernet
30 Specific CAN IDs in Modbus TCP / RTU Mode
DIN mounting
Radio link for serial transfer on the 2.4GHz band
one for a (P2P) or one for more (P2M)
Range Up to 700 meters with whip-antenna
Range Improves panel antenna < Br> Serial port: RS232 or RS485
supply and COM port is with shed terminals
antenna: R/SMA female
Simple Setup with Turn and Dip Switche
2.4GHz, 16 channels
Supply 10 to 30 VDC
Moxa A53, DB9 W/ADAPTER
2-port RS-422/485
Communication speeds up to 921.6 Kbps.
2KV overvoltage protection, IEC-61000-4-5 Level 3.
1.5KV insulated protection meets IEC-60747 -5-5
16C950 UART controller
RS-422 and RS-485 auto detection and switching technology
jumper and software free.
On-chip hardware automatic flow control to guarantee nothing data loss.
15KV ESD protection for all serial signals meets IEC-61000-4-2 standard.
Plug-n-Play, I / O address and IRQ assigned by BIOS.
Certified by CE , FCC, VCCI, BSMI, RoHS and Microsoft WHQL authentication.
Support Microsoft Windows, Linux and DOS OS.
Wireless Com Port - Can Peer-to-Peer connection
IEEE 802.11 a/b/g/n
2.4 GHz, 5 GHz Dual Band
1 Port RS232 or RS422 or 2-wire RS485
Max.Baud Rate: 921.6 Kbps
Operating temperature: -40 - +85°C
with COM Port Re-Director, TestView
± 15KV IEC ESD protection
Supply voltage: 5 - 12VDC / 2W
infrastructure, Soft AP, Roaming
sWifi config Mobile App for Android
Bluetooth from PC to the adapter provides RS232 port
External antenna.
Bluetooth 2.0.
With 2 pcs. as back-to-back link
provides connection between 2 COM ports
Wireless transfer of data between serial ports
Up to 100 meters
Antenna connector is RSMA female
Setup via AT commands
Must be powered from 5 - 40VDC via screw terminal
USB mini cable to A male - for power from 5VDC
2 x screw terminal for any external power supply
Is not battery-powered
Use Putty for testing/setup
Help with setup can be purchased additionally
Parallel til seriel omformer
Hastighed: 300 -19.200 bit/s
Handshake: XON / XOFF
Forsyning: Strømforsyning medfølger, 9 VAC, 400 mA
CNV-PAR232 er ikke bi-direktionel og kan derfor ikke sende meldinger fra printer til pc om evt. blækstatus, ”end of paper” m.m.
Two 16550 High performance UART (RS232) serial channels
Occupies one PCI or PCIe bus slot
Low Profile PCI Form Factor
Includes Low Profile PCI & Regular size PCI two brackets
Both USB A type and USB pin header connector on board to host connection
One RS232 DB9M and one RS232 10pin RJ45 serial ports on board
Includes one 10pin RJ45 – DB9M Bridge cable for 2nd DB9M port
5VDC Power output from each DB9M Port for POS device use application
2 Jumpers Individually enable / disable 5VDC output for each DM9M Port
On Board Molex mini 4Pin Power connector for sufficient DB9M 5V bus power from PC power supply
Supports 32bit/64bit Windows 7, Vista, XP, 2000, ME, 98SE
RS232 galvanic isolator, 3000VAC
With dual DC-DC converter, provides isolation both ways
Transmits Tx, Rx, RTS and CTS or DSR and DTR (selected)
Up to 115 kbit / s
Entrance: DB9 female, output: DB9 male
10-30VDC, screw terminal
DIN rail
Sæt udstyr med RS232, RS422 og RS485 interface på et Profibus system.
MODBUS RTU (RS232 / 422/485) equipment for Profibus DP network
MODBUS RTU slave devices are connected to the Profibus DP network
Optoisolerated RS422 / RS485 Repeater
3000vdc Glavanic isolation
2 threads RS485 is half duplex (switch-talk)
4 threads RS485 / RS422 A full duplex (both ways at the same time)
Translator from RS422 (4-wire) for RS485 (2-wire), semiduplex
automatic directional change and baud rate.
USB to Hart Bus Converter
to HART Short / Long Frame
to Hart Burst Mode
Point-to-point or Multi-Drop Hart mode
Up to 15 HART slave units < Br> Allow 2 Hart Master
Module Configuration Tools and HART communication
Power supplied by the USB port
Selectable 250Ω load resistance
Serial to USB converter with 1 x RS232/422/485 port
Respects the +/- 11 volt data signals
Galvanically isolated on the RSxxx output
Self-tuner Baud Rate
Automatic direction control
Powered from the USB port
USB connector: Type B
Supports USB 1.1, 2.0 and 3.0
COM port: terminal block
4 ports multiplexer (sæt), op til 900m
PCI Express parallel card with 1. DB25 port
Most drivers up to Win10 available in the Download
Isoleret RS485 repeater til DIN skinne
2 x RS232 serial ports with plug & amp; play
1 x TITAN BSP9216B (chipset)
1 x DB25 male connector on the card
1 x DB25 female for two DB9 male adapter cables included
Bus: universal PCI (5V and 3.3V) 32 bit 33MHz
RS232 signal: DCD, RxD, TxD, DTR, GND, DSR, RTS, CTS, RI
Max. bitrate: 921.6kbps
Each port with 16 bit FIFO for transmit & amp; review
IS support: Windows, Linux
0 ° C to 60 ° C
RS232 lysleder omformer m/DCE eller DTE omskifter
1 meters kabel til SER8PCI-K+ med 8 x DB9
Get a COM port on the Android Tablet or Android phone via USB port
Connect 1 x RS232 equipment to Android Tablet / phone
Connect to micro USB port on the Tablet / Phone
Baud rate up to 921.6 kbit / s
Supports HART Short / Long Frame
Supports Hart Burst Mode
Supports Point-to-point or Multi-Drop Hart mode
supports connection of up to 15 Hart slave devices
Allow 2 Hart Master
HC_Tool tool for module configuration and HART communication
support firmware update via Ethernet
PWR / TXRX indication LED
4KV ESD protection
built-in watchdog
Selectable 250Ω load resistance < Br> 4 Hart Channels
Support VXCOMM Technology
Built-in Web Server for Network Setting
UHF 433 MHz RS-232 adapter
RS-232 konfigureres via COM port
1 to 1 tilslutning
1 to N broadcast
Op til 200 meter
MOXA
4 x RS485/422 COM ports over fiber, fiber network
Extender over fiber with 4 x RS422 / 485
1 x 100 Mbit fiber
Screw terminal block (5 pole)
SFP slot for 100mbit Multi Mode LC Fiber
62 x 50 x 120 mm
Display 3 LEDs Displays TX / RX, Network and System Status
Supply 9 - 32 VDC (not supplied)
MOXA USB to RS422/485 converter
Galvanically isolated.
1-port RS-422/485 USB-to-serial converter
Compatible with USB 2.0
12 Mbps USB data rate
921.6 kbps maximum baud rate for super fast data transmission
Drivers provided for Windows, Windows Server, WinCE, and Linux
Mini DB9 female to terminal block adapter for easy wiring
LEDs for indicating USB and TxD/RxD activity
15 kV ESD protection for all serial ports
2 kV electrical isolation
Supports Windows 11
Serielportserver 2 x RS232 / 422 /485 MOXA Nport 5210
Compact design for easy installation
Socket modes: TCP server/TCP client/UDP
Easy-to-use Windows utility for configuring multiple device servers
Supports 10/100M Ethernet
Patented ADDC® (Automatic Data Direction Control) for 2-wire and 4-wire RS-485
SNMP MIB-II for network management
Auto Data Switch MP401B Parallel Printer Sharing Device
4 PCs can share the same parallel printer
Automatic switch to parallel printer
Active line is displayed with LED
Timeout programmable from 3 to 70 sec.
Supplied with 9VDC voltage supply
Plug: 5 pcs. DB25 female connector
2-port RS-422/485 high speed communication board
Windows 2000 / XP / 2003, Windows NT, Windows 95/98 / ME, WIN 7, WIN 8, WIN 10 32/64 Bit
Windows XP Embedded, WINDOWS 2003, 2008, 2012
DOS, FreeBSD 4.x, Linux 2.0.x (Alpha), Linux 2.2.x (Alpha), Linux Base
MOXA CP132I
Internet Communication controller with 1 x CAN bus, 1 x RS-232, 1 x RS-485 and 1 x Ethernet
10/100 Base-TX Ethernet controller
TCP / IP protocol
80 MHz CPU
1 x RS-232 port, 1 x RS-485 port and 1X CAN port can be used simultaneously
Max Transmission Speed up to 1M BPS for CAN and 115.2Kbps for RS-232 RS-485
7 -Segment LED Display
Software Configuration for Can and RS-232
Web Configuration
Up to 25 Ethernet Client Connections
Supports Virtual Com
1 Ports LTE Serial for Ethernet Gateway / Modem, RS232 / 422/485
GSM / GPRS / EDGE / UMTS / HSPA / LTE
Supports VPN and virtual computing
operating temperature 0- 55 ° C
IP30
12-48 VDC
DIN mounting (fittings included)
High-speed USB to RS232/422/485 adapter
Transmission speed - up to 921.6 kbps
Supports USB 1.2/2.0/3.0
3000V DC isolation on RS232/422/485
RS232/422/485 cannot be used simultaneously
Supplied via the USB port
Automatic RS485 Direction Control
Temperature range: -25°C - +75°C
DIN rail mounting
Windows 98/ME/2000/XP/Vista (32/64-bit)
Windows 7 / 8.1 / 10 (32/64-bit)
Win 2012
Linux
USB-C - Serial RS232 Adapter cable
USB Type C Han to 9-pole RS-232 Han connector with finger screws
Download speed 1 Mbps +
Supports Remote Wake-up and Power MM
1.8 meters
Extend the distance between PC and RS232 Equipment
Straight through network cable
RS232 serial port boost up to 1.2 km
Baud rate range: 300 - 200kbps
Supply voltage: DC9-24V (not included )
Optical isolation
isolation voltage: 2500Vrms pulse or 500 V = continuous
Dimensions: 100 mm x 50 mm x 20 mm
Weight: 350 g
2 COM ports over Ethernet, Internet
Each COM port can be RS232 or RS422 or RS485
RS232 Pin 1 - 8: DCD, RXD, TXD, DTR, GND, DSR, RTS, CTS
RS422 / RS485 4-W: Pin 1 - 5: TXD +, TXD, RXD +, RXD, GND
RS485 2-W: Pin 3 - 5: Data, Data +, GND
Baud Rate: 50 bps - 921Kbps
Data Bits: 5, 6, 7, 8
Parity: 1, 1.5, 2
Stop Bit: Odd, Even, None, Space, Mark
2 x RJ45 10 / 100mbit
Alarm: Relay output
Supply voltage: 12 - 48VDC 6.5WATT
Web Management
IP Version: IPv4 / IPv6. TCP Server, TCP Client, UDP Client
Virtual Com
Pair Connection
Supporter: XP to Win10, Server 2003, 2008, 2012
Size: 135 x 88 x 32 mm
DIN bracket
Module to Can 2.0a and B
ISO 11898-2 standard
Baudrate 10Kbps for 1M bps
software for setting CAN and RS232 / 422/485
Transparency between RS-232 / 485/422 Via CAN bus
Full duplex on RS-232/422 units are not supported
CAN Bus Baud Rate Configuration
CAN Accept Filter Configuration
CAN 2.0A or 2.0B Specific Choice
RS-232 / 485/422 Baud rate and data file setting
RS-232/485/422 Respond Options
Setting: Normal or pair connection
Supports Baud Rate conversion
Supports Modbus RTU/ASCII protocol
Supports two masters sharing one slave port
Raw data mode for most query-response protocols
Built-in web server for easy configuration (HTTP)
Redundant power inputs: PoE (IEEE 802.3af, Class 1) and DC jack
Allows automatic RS-485 direction control
Tiny form-factor and low power consumption
Read-cache ensures faster response
Extends serial cables up to 1600 meters or printer cables up to 180 meters.
RS232 galvanic isolator, 2500VAC
Transfers Tx, Rx, RTS and CTS
Up to 115 kbit / s
Input: DB9 female, output: DB9 male
RX, TX, ON indicator
12VDC / 100mA
External COM port over Ethernet and Internet.
RS232 seriesport via DB9 Han, or
RS422 / 485 port via screw terminal block
Power supplied from 12 - 48VDC. Has redundant DC input.
DIN mounting
RS485 for RS232 or RS422 for RS232
optoisulated RS232 for RS422 / 485 Converter
supply voltage is isolated against RS232 page
Supply voltage is isolated against RS485 / 422 page
Automatic Baud rate control
Repeater and splits an RS485 signal into 4 branches
RS485 master on input polls RS485 slaves with ID
Only asked RS485 slave responds only to master
No RS485 slave can poll the RS485 bus
2-wire RS485 - semi-duplex
Extend the star bus with more M485-REP4-I
Supply: 10 - +30VDC
Temp: -25 - +75°C
For DIN-Rail mounting
2 RS422/485 serielle porte til PCI Express
2 pcs. DB9 serial ports. DB25 parallel port for PCI Express
Mini PCI Expressadapter til PCI Express, med simkort holder
Gateway from Ethernet slave to PROFIBUS master
protocol / hierarchy: DP-V0 Slave
PROFIBUS Speed (Kbps) in 10 step from 9.6 - 12000
speed setting is automatic
Max. Input data length: 240 byte
Max. Output data length: 240 bytes
Address setting: 0 ~ 126 Set by DIP switch or EEPROM
Ethernet protocol: TCP / UDP server / client
Configuration: Web Configuration
4 COM ports via optical fiber cable
point to point or pount to 4 points
4 x RS232 ports up to 2km with multi mode cable
4 x RS232 ports up to 20km with single mode cable
Buy 100Mbit SFP Module (Multi Mode or Single Mode)
1 x 100 Mbit SFP for LC Duplex Fiber cable
4 x RS232 DB9 male connector
Setup via built-in Web server
62 x 50 x 120 mm
DIN fittings
Display 3 LEDs Displays TX / RX, Network and System Status
Supply voltage: 9 - 32VDC Redundant (not supplied)
Moxa MGATE 3180 1port RS232/422/485 Modbus TCP to serial.
External COM ports via Ethernet and Internet
3-in-1 Serial Port: RS-232, RS-422, OR RS-485
Modes: TCP Server, TCP Client, UDP
Ethernet Modem
Pair Connection
Real Com / Tty Drivers for Windows and Linux
2-wire RS-485 with Patented Automatic Data Direction Control (Addc®)
Built-in 15 kV ESD Protection for All Serial Signal
External COM ports via Ethernet and Internet
Easy IP Address Configuration with LCD Panel
10 / 100Mbit Auto-Sensing Ethernet
4 Serial Ports, With Support for RS422, and RS485 < Br> Built-in 15 kv ESD Surge Protection for All Serial Signals
Versatile Socket Operation Modes, Including TCP Server, TCP Client, and UDP
Choice of Configuration Methods: Web Console, Telnet Console, and Windows Utility
SNMP MIB-II for Network Management
-40 to 75 ° C Operating Temperature
Serial to HART Convert
Allows 2 pcs. Hart Masters
Point-to-Point or Multi-Drop Hart Mode
Possibility of connecting 15 HART modules
Point-to-point or multi-drop HART mode
for configuration of modules
Isolated COM 1: RS-232 / 422/485
PWR / RUN / ERR INDICATION LED
Built-in Watchdog
4 kV ESD protection
USB to RS485 converter, isolated
1 x RS485 7-pin terminal block
1 x USB-B
Speed: 300 ~ 115200 bps
For USB 1.1 / 2.0 (High Speed)
2500 VDC isolation on RS485 side
To DIN rail mounting
No external power supply required
Input +5 VDC from USB port
OS support WIN 98 / ME / 2000 / XP (32 / 64- bit) / Vista (32/64-bit) / 7 (32/64-bit) / 8 (32/64-bit) / 10 / Linux
Operating temp. -25 ° C ~ +75 ° C
USB cable (1.8m) included
CAN bus port on your computer via USB 1.1, 2.0 or 3.0 port
Powered from USB port
LED shows initialization and CAN bus status
Installs as a standard Windows COM port
CAN modes: Standard, Listen, Echo
Controlled using ASCII commands
API provided along with examples
Plug and play installation
CAN bus speed up to 1 Mbps
Supports CAN 2.0A and CAN 2.0B protocols
Drivers provided for Windows and Linux OS
Supports SocketCAN (slcan driver) since kernel 2.6.38+
Point-to-Point Fiber Converter RS232 / RS422 / RS485
Multi Mode 62.5 / 125 or 50 // 125my, wavelength 850nm
Power Supplied from 10 - 30VDC / 2 Watts
DIN Rail Bracket .
Up to 2km
ST plug
Repeater and splitter of an RS485 signal
Up to 3 branches, as a star connection
It is very IMPORTANT to avoid bus reflections.
Use M485-REP3-I if the RS485 bus is to be split out
For DIN Rail mounting
Optisk isolator med DB25 stik
Serial card for universal PCI, low backplane Universal PCI 3.3 / 5.0V
1x RS232
UART 16550 (16 Byte FIFO)
Speed 921 kbps
PCI Plug and Play
Drivers for Windows 95 for Win 7 / 2008 R2
Software compatible with DOS, Windows 3.11, OS/2, Linux and various. Unix
Seriel port: 2 x RS232, 1 x RS232/485 maks. 115 Kbps
Signaler: RS232: Rx , Tx , RTS , CTS
RS485: Data +, Data - (2-leder halv duplex)
Digital I/O: 6 indgange og 2 udgange TTL
Protokoller: TCP, PPP
Stik til digital I/O: Skrueterminaler
3/5V SIM kortholder indbygget
3 lysdioder viser GPRS- og systemstatus
Strømforsyning: 9 - 35 VDC maks. 4,8 Watt. medfølger ikke
Leveres med beslag til DIN skinne
External COM ports via Ethernet and Internet
Compact and but finding room for
Socket Modes: TCP Server / TCP Client / UDP
Windows Utility for Configuring Multiple Device Servers
Supports 10 / 100m Ethernet
2 x DB9 male
SNMP MIB-II for Network Management
Power supply included
USB 2.0 to 4 x RS232/422/485
High-Speed serial ports 921.6kbps
Driver for Windows, Linux, Mac OS X
LEDs for Power and TxD/RxD activity
ESD protection on USB and serial ports
2.5kV electrical isolation (ISO version only)
Bus powered (non-ISO), Self powered (ISO version)
Wide range of power input 9 - 54V DC
Metal housing
19-inch rack and wall mounts
Wide range of operating temperatures
DB9 female connector
1200 to 921600 baud
Supply 5 to 24 volts via USB or screw terminals
Built-in WiFi antenna
USB adapter cable included
1 port LTE serial to Ethernet gateway / modem, RS232 / 422/485
GSM / GPRS / EDGE / UMTS / HSPA / LTE
Supports VPN and virtual comport
Operating temperature -30 -70 ° C
IP30
Supplied via the 12-48 VDC
DIN rail mounting (bracket supplied)
Wifi CAN converter. CAN CAN bridge. CAN PC
two CAN channels
AP mode and station mode
Compatible with Socket (TCP Server, TCP Client, UDP)
Support: Ethernet, ARP, IP, ICMP, UDP, DHCP, DNS TCP)
DIP switch for terminating
Isolation: 1500VDC
CAN baud rate: 5kbit / s to 1Mbit / s
Wifi: 2.4GHz IEEE802.11a / b / g
Supply voltage: 9 - 30VDC
Consumption: 80mA @ 24VDC
Dimensions: 118 x 94 x 23 mm
Operating temperature: -40 - + 85 ° C
4 COM ports over Ethernet, Internet
Each COM port can be RS232 or RS422 or RS485
RS232 Pin 1 - 8: DCD, RXD, TXD, DTR, GND, DSR, RTS, CTS
RS422 / RS485 4-W: Pin 1 - 5: TXD +, TXD, RXD +, RXD, GND
RS485 2-W: Pin 3 - 5: Data, Data +, GND
Baud Rate: 50 bps - 921Kbps
Data Bits: 5, 6, 7, 8
Parity: 1, 1.5, 2
Stop Bit: Odd, Even, None, Space, Mark
2 x RJ45 10 / 100Mbit
Alarm: Relay output
Supply voltage: 12 - 48VDC 6.5WATT
Web Management
IP Version: IPv4 / IPv6. TCP Server, TCP Client, UDP Client
Virtual Com
Pair Connection
Supporter: XP to Win10, Server 2003, 2008, 2012
Size: 135 x 88 x 50 mm
DIN bracket
Modbus over the Ethernet or Internet
MODBUS server with 1 x RS232 and 1 x 422/485
Can run Device to Device
0/100 Mbps Ethernet port, auto MDI / MDIX, 10/100 auto, 1500V magnetic insulation only on
RS485 RS232 Modbus ASCII / RTU port, 1 RS422 / 485 Modbus ASCII / RTU port, 16V / 400W TVS isolated, RS485 automatic line control
9 ~ 30VDC power input, IP30 enclosure , DIN rail mounting structure, USB port (Modbus serial port expansion and capture of memory)
Monitor, manage and manage industrial devices
1 x RJ45 Ethernet port
2 x SFP slot for fiber transceiver (SM or MM)
Industrial EMC protection, temperature operation wide, -40 ° C ~ 85 ° C
Fast-Ethernet 2 x 100/1000 SFP Slots with RSTP Redundancy
4 software Selected RS485 / RS422 Serial ports, up to 921Kbps
TCP Server / Client, UDP, Virtual com and tunneling modes supported
Embedded Security with PPTP, IPSec or OpenVPN Client / Server
Redundant 12 ~ 48 VDC Power Entries
Configuration via Web Browser / Serial Console / Telnet / Windows Utility
Robust Metal Cabinet with wall or DIN rail
PCI Express parallelkort med 2 stk. DB25 stik
Serial Device Server for RS232 / RS422 / RS485 with WiFi